Brother P-Touch PT-2430PC Panduan Pengguna

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Pembuat label Brother P-Touch PT-2430PC. Brother P-Touch PT-2430PC 2 halaman. Brother labeller users guide
Juga untuk Brother P-Touch PT-2430PC: Brosur (4 halaman), Panduan Pengguna (2 halaman), Panduan Pengguna (2 halaman)

Halaman Cetak

Brother P-Touch PT-2430PC Panduan Pengguna

E n g l is h

Printed in China

www.brother.com

LW3960001

INTRODUCTION

Thank you for choosing the PT-2430PC. Your new P-touch labeler uses P-touch Editor Lite software, which is already installed on your labeler.

There is no need to install any software or drivers onto your PC in order to make creative labels. This manual includes important precautionary

information and simple instructions for operating your new P-touch labeler. Be sure to read the instructions before use and use the product in ac-

cordance with these instructions. Keep this manual handy for future reference. If new versions of the PT-2430PC software become available, this

manual may not reﬂ ect the updated features. Therefore, you may ﬁ nd that the software and the contents in this guide are different.

Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)

Responsible Party: Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA

TEL: (908) 704-1700

declares that the product: Product Name: P-touch Labeler PT-2430PC

Model Number: PT-2430PC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to cor-

rect the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁ cations not expressly approved by Brother Industries, Ltd. could void the user's authority to operate the equipment.

The enclosed interface cable should be used in order to ensure compliance with the limits for a Class B digital device.

Getting Ready

Review the names of P-touch labeler parts.

Feed & Cut button

LED lamp

Power

button

Tape exit slot

AC adapter (included)

connecter

USB port

Mode selector

switch

The PT-2430PC has 2 mode selector settings - "EL" and "E". The mode selector

switch is pre-set at the factory to the EL mode, for use with P-touch Editor Lite. For

E mode, you will need to install P-touch Editor 5.0, a more advanced labeling soft-

ware, and the required drivers from the enclosed CD. For details on how to install

the P-touch Editor 5.0, see "Starting P-touch Editor 5.0" below.

Connect the P-touch labeler's power supply.

When using the included AC adapter (AD-

24ES), insert the plug on the adapter cord

into the adapter jack on the bottom end of the

P-touch labeler. Insert the plug into the near-

est standard electrical outlet.

Connect the USB cable and start P-touch Editor Lite.

Connect the

Turn on the P-touch labeler.

USB cable.

The LED lamp will light up.

How to disconnect the P-touch

labeler

Exit P-touch Editor Lite by clicking on the

right.

To disconnect the labeler, click the icon in the computer's

task bar (

, or

Click Safely remove USB Mass Storage Device.

When The device can be safely removed is displayed,

turn off the P-touch labeler and disconnect the USB ca-

ble.

USER'S GUIDE

Install a tape cassette.

Open the cassette

Release Lever

cover.

Print head

Tape cutter

Verify that the P-touch labeler is

turned off. Open the cassette cover

as shown by the arrow in the above

illustration while pressing the part

marked "<<".

Windows

P o p - u p W i n d o w

A p p e a r s . S e l e c t

P - t o u c h E d i t o r

Lite and click OK.

Windows Vista

at the top

Starting P-touch Editor 5.0

SAFETY PRECAUTIONS

WARNING

• Always use the speciﬁ ed voltage and the included AC adapter (AD-24ES) for this machine to prevent any damage or failure.

• Unplug the power cord immediately and stop using the P-touch labeler during an electrical storm. There may be a remote risk of electric shock from lightning.

• Do not use the AC adapter in places of high humidity such as bathrooms.

• Do not overload the power cord.

• Do not place heavy objects on, or damage the power cord or plug. Do not forcibly bend or pull the power cord. When disconnecting the power cord from the power outlet, al-

ways hold the plug.

• To prevent ﬁ re or electric shock, make sure that the plug is fully inserted to the power outlet. Do not use an outlet that is loose.

• Do not get the machine/AC adapter/power plug wet, such as by handling them with wet hands or spilling beverages on to them.

• Do not disassemble or modify P-touch labeler/AC adapter/batteries.

• Do not use metallic articles, such as tweezers or a metallic pen, when exchanging the batteries.

• Do not throw into ﬁ re or heat up the battery.

• Disconnect the AC adapter, remove batteries and stop using immediately if you notice any abnormal odor, heat, discoloration, deformation or anything unusual while in use, or

in storage.

CAUTION

• To avoid injuries, do not touch the blade of the cutter unit or any metal parts near the print head.

• Remove the batteries and disconnect the AC adapter if you do not intend to use P-touch labeler for an extended period of time.

• Do not use old and new batteries together or mix alkaline batteries with other type batteries, or set the positive and negative end in the wrong position. Otherwise, the batter-

ies may leak or be damaged.

• To prevent damage or breakage, do not drop or hit P-touch labeler/AC adapter.

• Use only the USB cable included with the P-touch labeler.

General Precautions

• Depending on the location, material, and environmental conditions, the label may unpeel or become irremovable, the color of the label may change or be transferred to other

objects. Before applying the label, check the environmental condition and the material.

• Do not use the P-touch labeler in any way or for any purpose not described in this guide. Doing so may result in accidents or damage the machine.

• Use only Brother TZ tapes with this machine. Do not use tapes that do not have the

• Do not clean P-touch labeler with alcohol or other organic solvents. Only use a soft, dry cloth.

• Do not touch the print head with your ﬁ ngers anytime to prevent from a burn. Use a soft wipe (e.g. a cotton swab) when cleaning the print head.

• Do not put any foreign objects into the tape exit slot or AC adapter connector, etc.

• Do not place the P-touch labeler/battery in direct sunlight or rain, near heaters or other hot appliances, in any location exposed to extremely high or low temperatures (e.g. on

the dashboard or in the back of your car), high humidity, or dusty locations.

• Do not try to print labels using an empty tape cassette in the P-touch labeler. Doing so will damage the print head.

• Do not pull the tape being fed from the P-touch labeler, otherwise the tape cassette or P-touch labeler may be damaged.

Insert a tape

cassette.

Insert a tape cassette as shown in

the above illustration.

When using the P-touch labeler with

batteries, insert six new AA alkaline

batteries (LR6), making sure that

their poles point in the correct direc-

tions. Always replace all six batter-

ies at the same time using brand

new ones.

2000 User

Go to My Computer and open Removable Disk, then

start P-touch Editor Lite by double-clicking

PTLITE10.

EXE.

XP User

It will take longer than usu-

al to start P-touch Editor

Lite when connecting P-touch

labeler to your computer for the

first time. If the software does

not start automatically when you

connect the machine, you may

User

launch it from My Computer.

Start P-touch Editor Lite by dou-

ble-clicking

PTLITE10.EXE.

Pop-up Window

Appears. Click

P-touch Editor

Lite.

*Microsoft Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States and other

countries.

*The name of other software or products used in this document are trademarks or registered trademarks of the respective

companies that developed them.

If you would like to use the more advanced software that is available for your P-touch labeler,

Move the mode selector

you are able to install P-touch Editor 5.0 from the included CD-ROM. This advanced software

switch on the back of the

will give you greater label making functionality.

P-touch labeler to the "E"

Do not connect the P-touch labeler to your PC before you begin the P-touch Edi-

position before connecting

tor 5.0 installation. For details on how to install P-touch Editor 5.0, see the in-

the USB cable.

stallation guide in the included CD-ROM.

International ENERGY STAR

Compliance Statement

The purpose of the International ENERGY STAR

promote the development and popularization of energy-efﬁ cient of-

ﬁ ce equipment.

As an ENERGY STAR

Partner, Brother Industries, Ltd. has deter-

mined that this product meets the ENERGY STAR

energy efﬁ ciency.

mark.

Close the cassette

cover.

• Make sure that the end of the tape feeds under the tape guides.

• If the ink ribbon is loose, use your ﬁ nger to wind the toothed

wheel in the direction of the arrow on the cassette.

• Use only Brother tapes with the P-touch labeler.

• For initial use of the tape, install the tape. Then, push in the Feed

& Cut button to cut the tape.

• Make sure that the release lever is up when closing the tape cover.

The tape cover cannot be closed if the release lever is pressed down.

Auto Power Off Function

When the P-touch labeler is operating on battery power only,

it will turn off automatically if not used for a period of 20 min-

utes. The message "Unsafe Removal of Device" may be

displayed depending on the Operating System running on

your PC. Any data being displayed will be saved. When you

turn the labeler back on, click on the Editor Lite icon to re-

sume creating your label.

P-touch Editor Lite

starts immediately.

For details on using

P-touch Editor Lite,

see the back of this

sheet.

Do not turn off the power or remove the labeler while

using P-touch Editor Lite.

When using

Windows Vista

When connecting the device for the ﬁ rst time, perform the

scan and then select the Always do this for software and

games check box on the dialog box displayed when the

scan completes. P-touch Editor Lite will start automatically

the next time you connect the P-touch labeler.

Program is to

guidelines for