2N EasyGate Pro Mulai Cepat - Halaman 4
Jelajahi secara online atau unduh pdf Mulai Cepat untuk Gerbang 2N EasyGate Pro. 2N EasyGate Pro 4 halaman. Umts gateway
Juga untuk 2N EasyGate Pro: Mulai Cepat (4 halaman), Mulai Cepat (2 halaman), Mulai Cepat (4 halaman)
Halaman Cetak
Outgoing call
• Suppose
that
the
inserted, the PIN entered or not required,
and EasyGate is registered to the network –
the LED Mobile network is permanently on.
• Hook off the telephone, you can hear the
dial tone and the Line LED starts flashing.
• Dial
the
subscriber
receives tone dialing (DTMF) by default. If
your telephone transmits pulse dialing only,
program EasyGate to receive pulse dialing.
When you make a delay in your dialing
longer
than
5s
connection is established.
• If the called subscriber is available, you can
hear the ringing tone. If not, you can hear
the busy tone or any of the mobile network
provider's messages.
• When the called subscriber answers the call,
the call is established. The Line LED is
permanently on during the call.
• Hang up to terminate the call. The Line LED
goes off. If the called subscriber is the first
to hang up, you can hear the busy tone, you
have to hang up.
Incoming call
• An incoming call is signaled by ringing. The
Line LED flashes during ringing.
• Hook off the phone to establish the call. The
Line LED is permanently on during the call.
• For call termination see the Outgoing call
section.
Configuration over USB
• For
PC
configuration
necessary
to
Connect EasyGate to PC using USB cable.
In the GSM network data transfer is suspended during voice calls and do
not continue until the voice call is finished. UMTS network is able to
transfer data concurently with voice.
EC Declaration of Conformity
Hereby, 2N TELEKOMUNIKACE a.s. declares that the radio equipment type 2N
directives 2014/53/EU and 2011/65/EU. The full text of the EU declaration of conformity is available at the internet
address www.2n.com.
2N TELEKOMUNIKACE a.s. – Modřanská 621, Prague 4, 143 01
SIM
card has been
number.
EasyGate
(programmable),
of
EasyGate
install
PCManager UNI.
• Virtual serial port(USB serial port FTDI) is
created immediately after linking PC and
EasyGate. This port is used by PCManager to
communicate with EasyGate. When the port
isn't activated automatically use driver at
www2n.com.
• The COM port number of virtual serial port
has to be set in PCManager.
• Detailed description is in the product manual
at wiki.2n.com.
Data connection over USB
the
• Easy Gate can be used for high speed
connection to internet (up to 3,6 Mbps
download).
• You have to install USB drivers for UMTS
module. Drivers are at www.2n.com. You
have to select 32 bit drivers or 64 bit drivers
according to your system.
• For internet connection you must set the
APN.
Use
menu and set APN to the APN name of your
mobile internet provider.
• You have to set phone connection in your PC
using Network connection setting. Select
modem 'SimTech HS-USB Modem 9000' for
this
connection.
parameters
number) according to information from your
mobile
provider
'internet', Keyword is empty an Dial number
*99***1#).
• Finally
use
connection to internet.
is
PCManager,
select
Set
the
(Username,
Password,
(obviously
button
'Dial'
to
®
EasyGate is in compliance with
2018v2.22
GSM&SIM
connection
Dial
Username
establish