Fujitsu FI-6230 Memulai - Halaman 5
Jelajahi secara online atau unduh pdf Memulai untuk Printer Fujitsu FI-6230. Fujitsu FI-6230 23 halaman. Color duplex workgroup scanners
Juga untuk Fujitsu FI-6230: Panduan Memulai (20 halaman), Brosur & Spesifikasi (2 halaman), Buku Petunjuk (10 halaman), Pembersihan dan Pemeliharaan (47 halaman)
Halaman Cetak
Do not put liquids inside the scanner.
Do not insert or drop metal objects in to the scanner.
Do not scan wet documents or documents with paper
clips or staples. Do not splash or allow the scanner to
get wet.
If foreign objects (water, small metal objects, liquids,
etc.) get inside the scanner, immediately turn off the
scanner and disconnect the power plug from the
power outlet. Then, contact the store where you
bought the scanner or the Maintenance Service
Center. Pay particular attention to this warning in
households where there are small children.
Unplug the scanner when a trouble occurs.
Immediately unplug the scanner when a trouble
occurs.
Never cut the ground connection until the scanner is
unplugged from the power outlet.
Do not touch the inside of the scanner
unless necessary.
Do not take apart or modify the scanner. The inside of
the scanner contains high-voltage components.
Touching these components might cause electric
shock or fire.
Do not use the scanner if you smell a
strange odor.
If you detect heat coming from the device or detect
other problems such as smoke, strange smells or
noises, immediately turn off the scanner and then
disconnect its power plug. Make sure that any smoke
coming from it has stopped, before contacting the
store where you bought the scanner or an authorized
FUJITSU scanner service provider.
Do not use aerosol sprays near the scanner.
Do not use any aerosol sprays or alcohol based
sprays to clean the scanner.
Dust blown up by strong air from the spray may enter
the inside of the scanner. This may cause the scanner
to fail or malfunction.
Sparks, caused by static electricity, generated when
blowing off dust and dirt from the outside of the
scanner may cause a fire.
Do not place the scanner within the reach of
small children.
To avoid injuries, do not place the scanner in an area
where small children may be able to reach.
Do not touch the heated section for a long
time.
Do not touch the heated section such as the bottom of
the scanner for a long time.
Doing so may cause a low-temperature burn on your
skin.
Do not cover the scanner with something
during its operation.
Do not use the scanner while covered with a blanket,
etc. Doing so may raise the temperature inside and
cause a fire.
Do not use the scanner where it gets wet.
Do not use the scanner at a place such as a
bathroom, shower room, or swimming pool where it
may easily get wet. Doing so might cause electric
shock or fire.
fi-6140/fi-6240/fi-6130/fi-6230 Image Scanner Getting Started
Do not install the scanner on unstable
surfaces.
Make sure that the scanner is installed on a flat, level
surface and that none of its parts extend beyond the
surface top, such as a desk or table. Do not install the
scanner on unstable surfaces. Install the scanner on a
level surface that is free of vibration to prevent it from
falling.
Install the scanner on a strong surface that will
support the weight of the scanner and other devices.
Do not block the ventilation ports.
Do not block the ventilation ports. Blocking the
ventilation ports generates heat inside of scanner,
which may result in fire or scanner failure.
Do not place heavy objects or climb on top
of the scanner.
Do not place heavy objects on the scanner or use the
scanner's surface top to perform other work. Improper
installation might cause injuries and equipment
failure.
Firmly insert the power plug.
Firmly insert the power plug as far it can go into the
power outlet.
Avoid any contact when scanner is in use.
Avoid touching any scanner mechanism during
scanning since this may cause injuries.
Do not use the scanner immediately after
moving it from a cold place into a warm
room.
Do not use the device immediately after moving it
from a cold place into a warm room. Condensation
may occur, which might lead to scanning errors. Let
the device dry about one or two hours before you use
it.
Before moving the scanner, disconnect the
power plug from the power outlet.
Do not move the scanner with the power and interface
cables connected as this can damage the cables,
which can later cause fire, electric shock as well as
injury.
Before moving the scanner, be sure to disconnect the
power plug from the power outlet, and all other data
cables.
Make sure that the floor is free of any obstructions.
Protect the scanner from static electricity.
Install the scanner away from strong magnetic fields
and other sources of electronic noise. Also, protect
the scanner against any static electricity, which can
cause the scanner to malfunction.
Disconnect the power plug from the power
outlet when the scanner is not used for a
long period of time.
When the scanner is not going to be used for a long
period of time, be sure to disconnect the power plug
from the power outlet for safety.
Do not install the scanner in the direct
sunlight.
Do not install the scanner under direct sunlight or near
heating apparatus. Doing so might cause excessive
heat to build up inside the scanner, which can cause
scanner trouble or even fire. Install the scanner in a
well-ventilated location.
iv