Indesit FDEF31111 Informasi Layanan - Halaman 7
Jelajahi secara online atau unduh pdf Informasi Layanan untuk Mesin pencuci piring Indesit FDEF31111. Indesit FDEF31111 20 halaman.
Halaman Cetak
- 1. Table of Contents
- 2. Safety Notes & General Servicing Advice
- 3. General Information and Console Panel
- 4. VIRTUAL SENSORS Description and Operation
- 5. Additional Component Descriptions
- 6. Auto Test Cycle
- 7. Fault Codes & Diagnostics
- 8. Thermistor Resistance Chart
- 9. Wiring Diagram
- 10. General Dishwashing Information
Indesit
Company
FILLING SEQUENCE (with Virtual Sensors)
Once a program has been started, the first action of the dishwasher will be to drain down until the
"D-Sensor" registers empty + 15 seconds.
Thereafter, the W-Sensor runs for 40 seconds at 1400 rpm with the bottom delivery outlet open, to
confirm that the tub is actually empty (if not, after three unsuccessful attempts error "F15" will be
displayed).
The machine then starts to fill — an operation that will be completed in two steps:
1.
Static fill: the fill solenoid valve is piloted to open by the Main Module, and will admit
approximately 2.0 litres of water, measured by the Water Turbine. When this threshold is
reached, the Wash Pump ("W-Sensor") runs at 1400 rpm with the bottom delivery outlet open,
to confirm whether or not the machine is in Full status. If the Full condition is satisfied, the
dynamic fill will start.
Note: The BLAC Wash Pump Motor running at 1400 rpm on the bottom outlet, full status will
register with approximately 1.5 litres of water.
2.
Dynamic Fill: with the BLAC Wash Pump running (at 1400 rpm, bottom delivery outlet), the fill
solenoid valve is activated and held open by the Main Module until the water level increases to
around 3.5/3.8 litres (depending on the cycle selected).
If full status is confirmed by the "W-Sensor", the machine will continue washing as normal.
Sensor Key:
Possible Filling/Draining Errors
Machine is not emptying
Once a program has been started, the first action of the dishwasher will be to drain until the
"D-Sensor" registers empty + 15 seconds. Thereafter, the "W-Sensor" runs for 40 seconds at
1400 rpm with the bottom delivery outlet open, to confirm that the tub is actually empty (if not, after
three unsuccessful attempts error "15" will be displayed).
The machine then starts to fill - an operation that will be completed in two steps:
Machine's inlet Water Tap is OFF.
Static fill: The fill solenoid is piloted to open. The Main Module doesn't receive any information from
the Turbine (because no water in entering the machine). After a short time the machine will bleep
time and H will be displayed, is displayed (Warning to the user that no water is entering the machine)
after a further period the machine times out and 06 fault will display.
Turbine out of Range
Static fill: The fill solenoid is piloted to open. The Main Module does not receive any information
from the Litre-count turbine. After one minute during which the solenoid valve remains open and
approximately 2.4 litres of water have entered the machine, the Wash Pump (W-Sensor) runs at
1400 rpm with the bottom delivery outlet open to confirm
W-Sensor Full status. The cycle moves on to dynamic fill.
Dynamic fill: The speed of the Wash Pump is increased to 2400/2500 rpm (depending on the cycle
selected) and the tub continues to fill until the motor torque registers at a value corresponding to Full
status, at which point the machine continues washing as normal.
continued on next page...
Service Manual UK
D-Sensor: Drain Pump used as Sensor
W-Sensor: Wash Pump used as Sensor
7 of 20
English