Indesit DD60C2C /UK Panduan Petunjuk Pengoperasian - Halaman 3
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Kompor Indesit DD60C2C /UK. Indesit DD60C2C /UK 28 halaman. Free standing electric cooker
Halaman Cetak
Installation
WARNING - THIS APPLIANCE MUST BE EARTHED.
Mains Connection
Your cooker should have been checked to ensure
that the voltage corresponds with your supply
voltage, this is stated on the rating plate, which is
situated on the outer rear panel.The model number
and the serial number are located on the front of the
cooker, as shown on the Features page.
The cooker must be connected by a competent
person such as one who is a, NICEIC registered
contractor to a suitable double-pole control unit with
a minimum rating of 32A and a minimum contact
clearance of 3mm (applicable to newer properties,
older properties where a 30A double pole control unit
and a minimum contact clearance of 3mm is
acceptable).
The double pole control unit should be fitted
adjacent to the cooker, in accordance with IEE
regulations.The control unit must be within 2 metres
of but not directly above the appliance and should
be easily accessible in the event of an emergency.
The power supply cable should conform to B.S.6004
with a conductor size of 6mm
Access to the mains terminals is gained by
removing the rear access cover. The mains cable
must pass through the cable clamp adjacent to the
terminal block. Sufficient cable should be used to
allow the cooker to be pulled out for servicing.
Ensure that the mains cable is routed away from
any brackets affixed to the rear panel and is not
trapped to the rear wall when pushing the cooker
into position between cabinets.
For the installation of the feeding cable carry out the
, minimum.
2
following operations:
1 Open the terminal
board by inserting a
screwdriver into the
bottom tabs of the
cover. Use the
screwdriver as a lever
by pushing it down to
open the cover (see
diagram).
2 Loosen the cable
clamp screw and
remove it, using a
screwdriver as a lever
(see figure).
3. Fasten the wires
under the screw heads,
respecting
the colour code:
Black/Blue (N), Red/Brown (L) and Bare Wire/Yellow-
Green (
).
Once the connections have been made, tighten all
the terminal screws fully.
Fasten the supply cable in place with the clamp
and close the cover of the terminal board.
Levelling
Four feet are fitted which can be adjusted up or
down to set the height (900mm - 930mm) and level
the cooker.
The feet can be simply screwed in or out to lower or
raise the cooker.
After the correct height is achieved, lock the feet
into position by tightening the locking nut using an
open ended spanner.
CAUTION: Some soft floor coverings may get
damaged if the cooker is not moved carefully.
NOTE: Ensure oven shelves are level by using a
spirit level on the rod shelves.
Siting the Cooker
The cooker is designed to fit between kitchen
cabinets spaced 600mm apart.
The space either side need only be sufficient to
allow withdrawal of the cooker for servicing and
cleaning. It can be used with cabinets one side or
both as well as in an angled corner setting.
It can also be used freestanding.
Adjacent side walls which project above hob level,
must not be nearer to the cooker than 150mm and
should be protected by heat resistant material. Any
overhanging surface or cooker hood should not be
nearer than 650mm.
Note: This appliance must NOT be fitted on a
platform.
Moving the Cooker
Note: Take care in moving the cooker as it is
heavy.Take care to ensure that any floor
covering is not damaged.
Before moving your
cooker, switch off at
the cooker control
unit, ensure that it is
cool.
Open the grill door
sufficiently to allow a
comfortable grip on
the underside front
edge of the oven
roof, avoiding any
grill elements.
3
GB