Indesit IS50D1S Panduan Petunjuk Pengoperasian - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Kompor Indesit IS50D1S. Indesit IS50D1S 12 halaman.

Halaman Cetak

Indesit IS50D1S Panduan Petunjuk Pengoperasian

Positioning

! ! ! ! ! This unit may be installed and used only in

permanently ventilated rooms according to the

British Standards Codes Of Practice: B.S. 6172/B.S.

5440, Par. 2 and B.S. 6891 Current Editions. The

following requirements must be observed:

a ) a )

a ) a ) The cooker should not be installed in a bed sitting

a )

room with a volume of less than 20m

installed in a room of volume less than 5m

vent of effective area of 110cm

installed in a room of volume between 5m

10m

a supplementary airvent area of 50cm2 is

required, if the volume exceeds 11m

required. However, if the room has a door or a

window which opens directly to the outside no air

vent is required even when the volume is between

and 11m

b )

b )During prolonged use of the appliance you may

b )

consider it necessary to open a window to the

outside to improve ventilation.

c ) c )

c ) c ) If there are other fuel burning appliances in the

c )

same room, B.S.5440 Part 2 Current Edition,

should, be consulted to determine the requisite air

vent requirements.

Levelling

If it is necessary to level the

appliance, screw the

adjustable feet into the places

provided on each corner of the

base of the cooker ( see

figure ).

The legs* fit into the slots on

the underside of the base of

the cooker.

Installation of the cooker

The appliance can be installed next to furniture units

which are no taller than the top of the cooker hob.

The wall in direct contact with the back panel of the

cooker must be made of non-flammable material.

During operation the back panel of the cooker could

reach a temperature of 50°C above room

temperature. For proper installation of the cooker,

the following precautions must be taken:

a ) a ) The appliance can be placed in a kitchen, dining

a ) a )

a )

room or bedsit, but not in a bathroom.

b )All furniture around the appliance must be placed

b )

at least 200 mm from the top of the cooker,

should the surface of the appliance be higher than

the worktop of this furniture. Curtains should not

c ) c ) Any hoods must be installed according to the

c ) c )

c )

d )

d )If the cooker is installed beneath a wall cabinet,

d )

. If it is

an air

is required, if it is

e ) e ) The wall in direct contact with the back panel of

e ) e )

e )

and

no airvent is

f ) f ) f ) f ) f ) The cooker is fitted with a safety chain that must

Fig. A

be placed behind the cooker or less than 200 mm

away from the sides of the appliance.

requirements in the installation manual for the

hoods themselves.

the latter must be situated at a minimum of 420

mm above the hob. The minimum distance

between the worktop and kitchen units made of

combustible material is 700 mm (Fig. A).

the cooker must be made of non-flammable

materials.

be attached to a hook, secured to the wall behind

the appliance.

! Some models can have their gas connection

inverted. It is important to make sure the safety

chain is always situated on the side which

corresponds to the hose holder (Fig. B).

HOOD

600

Min.

mm.

Fig. B

Gas connection

T he cooker should be connected to the gas-supply

by a corgi registered installer. During installation of

this product it is essential to fit an approved gas tap

to isolate the supply from the appliance for the

convenience of any subsequent removal or

servicing. Connection of the appliance to the gas

mains or liquid gas must be carried out according to

the prescribed regulation in force, and only after it is

ascertained that it is adaptable to the type of gas to

be used. If not, follow the instructions indicated in

the paragraph headed "Adaptation to different gas

types". On some models the gas supply can be

connected on the left or on the right, as necessary;

HOT PARTS

to change the

connection, reverse the

position of the hose

holder with that of the

cap and replace the

gasket (supplied with

the appliance). In the

case of connection to

liquid gas, by tank, use

pressure regulators that

conform to the