Indesit RID60C2/UK Panduan Petunjuk Pengoperasian - Halaman 20
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Kompor Indesit RID60C2/UK. Indesit RID60C2/UK 28 halaman. Free standing electric cooker
![Indesit RID60C2/UK Panduan Petunjuk Pengoperasian](/uploads/products/server2/2504736/2504736.jpg)
Care and Cleaning
Control Panel:
Wipe with a damp cloth and polish with a dry cloth.
GB
Stainless trims
Regularly wipe with a clean, damp cloth and polish
with a clean dry cloth.
Grill Door:
Wipe over the grill door decorative outer panel; with
a cloth wrung out in warm soapy water, then after
wiping with a cloth wrung out in clear water, dry with
a soft clean cloth.
Do not use scouring pads or abrasive powder
which may scratch the surface.
Ensure that the glass panel (where fitted) is not
subjected to any sharp mechanical blows.
Grill:
Remove the grill pan and the wire grid food support,
it is best to wash these items immediately after each
use to prevent stains from being burnt on when used
again. Wipe out the Grill compartment, use a fine
steel wool soap pad to remove stubborn stains from
the compartment.
Main oven:
1. Glass Door - open the oven door fully.The glass
panel may now be cleaned. Stubborn stains can
be removed by using a fine steel wool soap pad.Do
not use scouring pads, or abrasive powder, which
will scratch the glass. Ensure that the glass panel
is not subjected to any sharp mechanical blows.
For slight soiling the inner glass panel may be
cleaned, while still warm. For removing stubborn
stains see "Care and Cleaning" chapter.
2. Remove the rod shelves and meat pan. Use a fine
steel wool soap pad to remove stubborn stains from
the rod shelves,meat pan and the floor of the oven.
Refer to the instructions in "Care and Cleaning"
chapter, for cleaning the shelf supports. Do not use
aerosol cleaners on this oven as they could
adversely affect the fan motor unit, and cannot be
wiped off the fan blade.
Replacement oven lamp:
WARNING: To avoid electric shocks - please
ensure that the electricity supply to the appliance
is switched off and the appliance is fully cold,
before removing the lamp lens.
Open the oven door and remove the rod shelves.
Using a suitable cloth to protect the fingers grip the
light glass dome, unscrew anti-clockwise and lift.
Reach into the aperture and unscrew the lamp anti-
clockwise. Fit replacement lamp (25W 300°C rated
SES), refit dome.
20
Wall-mounted splash panel:
A wall-mounted splash panel is available as an
optional extra from our Parts Department (see Key
Contacts, back page).
Care must be taken that rating label edges are not
lifted during cleaning and furthermore that the
lettering is not blurred or removed. For details of
your nearest Service Centre please see the separate
service leaflet. If you have any queries regarding
service or spares, our Parts and Service Division will
be pleased to advise.
See Key Contacts, back page, for details.
Take particular care not to damage the inner
surface of the door inner glass that is coated with
a heat reflective layer.Do not use scouring pads,
or abrasive powder, which will scratch the glass.
Ensure that the glass panel is not subjected to
any sharp mechanical blows.
Stubborn stains can be removed by using a fine steel
wool pad. For slight soiling the inner glass panel may
be cleaned, while still warm, without removing it from
the door. After cleaning, rinse and dry with a soft cloth.
CLEANING THE DOORS
SIDE OPENING DOORS
Cleaning the door glass is the same as the drop
down doors,except take care to support the weight
of the inner glass when removing and refitting.
DROP DOWN DOORS
Remove the door inner glass as follows.
1. Open the door fully and unscrew the two screws
securing the glass panel so that the securing
brackets can be turned.There is no need to remove
the screws completely.
2. Turn the brackets so that the glass can be removed
and cleaned at the sink (Fig. 1.)
3. The inside of the outer door glass can now be
cleaned while still fitted to the cooker.
NEVER OPERATE THE COOKER
WITHOUT THE INNER DOOR GLASS IN
POSITION.
Refit the door inner glass as follows.
1.Turn the two securing
brackets back to their original
position to retain the glass and
tighten the screws. (Fig. 2.)