Indesit W83 Petunjuk Instalasi dan Penggunaan Manual - Halaman 10
Jelajahi secara online atau unduh pdf Petunjuk Instalasi dan Penggunaan Manual untuk Mesin Cuci / Pengering Indesit W83. Indesit W83 17 halaman. Indesit washing machine instruction for installation and use
Halaman Cetak
The washing machine
does not drain or spin.
Does
the
selected
programme incorporates
water draining? Some
programmes stop at the end
of the wash cycles and
draining will have to be
selected manually.
Is
the
"Anti-crease"
function -where provided -
enabled? This function
requires manual selection for
draining.
Is the drain pump clogged?
To check it, turn off the water
supply, unplug the washing
machine and follow the
instructions on page 12, or
call for technical assistance.
Always get
assistance from
authorised
technicians and
always insist on
original spare parts.
Technical characteristics
Model
W 83
Dimensions
width 59,5 cm
height 85 cm
depth 52,5 cm
Capacity
from 1 to 5 kg
Electrical
voltage 230/240 Volt 50 Hz
connections
maximum absorbed power 2050 W
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0,05 MPa (0,5 bar)
drum capacity 40 litre
Spinning speed
up to 800 rpm
Control programs in
programme 3; temperature 60°C; press Extra Economy button; carried out with 5 kg load.
compliance with
IEC regulation 456
This appliance conforms with the following E.E.C. directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications
9
Is the drain hose kinked?
The tract of the drain hose
must be as straight as
possible. Make sure the drain
hose is not squashed or
kinked.
Is the washing machine's
drain duct clogged? Is there
an extension of the drain
hose? If so, is it positioned
incorrectly, blocking the
water flow?
Excessive vibration
during the spin cycle.
Have all transit screws been
removed durind instal-
lation? See the following
page
on
installation
procedures.
Has the washing machine
been levelled correctly? The
levelling of the appliance
should
be
checked
periodically. Adjust the feet
and check them with a level.
Is there space between the
machine and adjacent
units? If it is not a built-in
model, the washing machine
will oscillate a bit during the
spin cycle. A few cm of space
should therefore be left
around it.
The washing machine
leaks.
Is the metal ring of the inlet
hose properly attached?
Turn off the water supply,
unplug the appliance and try
tightening its attachment
without forcing it.
Is the detergent dispenser
obstructed? Remove and
wash it under tap water.
Is the drain hose well
attached? Turn off the water
supply, unplug the appliance
and
try
tightening
attachment.
Too much foam.
Is the detergent appropriate
for machine washing?
Check whether the definition
on its label reads "for machine
wash" or "hand and machine
wash", or any other similar
wording.
Is the correct amount being
used? An excessive amount
of
detergent,
producing too much foam,
does not guarantee a more
effective wash, and causes
scaling in the internal parts of
the appliance.
If, despite all checks, the
washing machine fails to
function and the problem
persists, call your nearest
authorised Customer Service
Centre, providing the following
its
information:
- the nature of malfunction
- the model type no. (Mod. ....)
- the serial number (S/N ....)
This information can be found on
the data plate situated at the
back of the washing machine.
besides