Indesit PAA642IWH Manual - Halaman 6

Jelajahi secara online atau unduh pdf Manual untuk Kompor Indesit PAA642IWH. Indesit PAA642IWH 8 halaman.

Halaman Cetak

PRODUCT DESCRIPTION

DAILY USE

HOW TO USE THE HOB

Do not let the burner ame extend beyond the edge of the pan.

IMPORTANT: when the hob is in use, the entire hob area may become hot.

•

When using models with an ignition button to ignite one of the burners,

press it and then press down the corresponding knob as far as possible

and turn it anticlockwise towards the maximum setting.

•

This burner safety device shuts o the gas supply to the burner if the ame

goes out accidentally (because of sudden draught, an interruption in the

gas delivery, boiling over liquids, etc.).

•

The knob must not be pressed for more than 15 sec. If, after that

time has elapsed, the burner does not remain lit, wait at least one

minute before trying to light it again.

NOTE: should particular local conditions of the delivered gas make the

ignition of burner di cult, it is advisable to repeat the operation with

the knob turned to the small ame setting.

The burner might go out when the knob is released. This means that the

safety device has not warmed up enough. In this case, repeat the operations

described above.

If the burner ame is accidentally extinguished, switch o the burner control

and do not try to ignite for at least 1 minute.

PRACTICAL ADVICE FOR USING THE BURNERS

This hob has burners of di erent diameters. For better burner performance,

please stick to the following rules:

•

use pots and pans with bottoms the same width as that of the burners

or slightly larger (see table on the right);

•

only use at-bottomed pots and pans;

•

use the correct amount of water for cooking foods and keep the pot covered;

•

make sure pots on the grates do not protrude beyond the edge of the hob;

•

In the case of pans with convex bottoms (WOK), use the support grille

(not provided), which should be positioned only on the multi-ring burner;

•

avoid accidentally knocking the hob with pans, racks or other kitchen utensils;

•

do not leave empty steak grills over the lit burner for longer than 5 minutes.

IMPORTANT: improper use of the grids can damage the hob: do not

position the grids upside down or slide them across the hob.

BURNER

Rapid

Semi-rapid

Auxiliary

Do not use:

•

cast iron griddles, ollar stones, terracotta pots and pans;

•

heat di users such as metal mesh, or any other types;

•

two burners simultaneously for one receptacle (e.g. sh kettle).

1. Removable panstand grids

2. Semi-rapid burner

3. Semi-rapid burner

4. Rapid burner

5. Auxiliary burner

6. Semi-rapid burner control knob

7. Semi-rapid burner control knob

8. Rapid burner control knob

9. Auxiliary burner control knob

10.

POT Ø

From 24 to 26 cm

From 16 to 22 cm

From 8 to 14 cm

Electric ignition button

ADAPTING TO DIFFERENT TYPES OF GAS

This operation must be performed by a quali ed technician.

If the appliance is intended to operate with a di erent gas from the gas

type stated on the rating plate and information label on the top of the hob,

change the injectors.

Remove the information label and keep it with the instructions booklet.

Use pressure regulators suitable for the gas pressure indicated in the

Instruction:

•

the gas injector must be changed by After Sales Service or a quali ed

technician;

•

injector not supplied with the appliance must be ordered from After

Sales Service;

•

adjust the minimum setting of the taps.

NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas

setting screw must be tightened as far as it will go.

IMPORTANT: should you experience di culty in turning the burners

knobs, please contact the After Sales Service for the replacement of

the burner tap if found to be faulty.

IMPORTANT: when gas cylinder is adopted, the gas cylinder or gas

container must be properly settled (vertical orientation).

REPLACING THE INJECTORS see the injector table in the Safety instructions

This operation must be performed by a quali ed technician.

•

Remove grids (A).

•

Extract burners (B).

•

Using a socket spanner of the appropriate size unscrew the injector (C),

to be replaced.

•

Replace it with the injector suitable for the new type of gas.

•

Re-assemble the injector in (D).

Before installing the hob, remember to a x the gas calibration plate supplied

with the injectors in such a way that it covers the existing information relating

to gas calibration.

Symbols

Shaded circle

Tap closed

Maximum opening/

Large ame

delivery and electric ignition

Minimum opening

Small ame

or reduced delivery