Kohler Command PRO CH26 Panduan Pemilik - Halaman 7

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Mesin Kohler Command PRO CH26. Kohler Command PRO CH26 8 halaman. Command series
Juga untuk Kohler Command PRO CH26: Panduan Pemilik (21 halaman), Panduan Pemilik (21 halaman), Panduan Pemilik (21 halaman), Panduan Pemilik (21 halaman), Panduan Pemilik (14 halaman)

Halaman Cetak

Fuse Replacement

This engine has three (3) blade type automotive

fuses. Replacement fuses must have same

rating as blown fuse. Use fuse chart below to

determine correct fuse.

Wire Color

2 Solid Red Wires

1 Red Wire with Black Stripe

1 Red Wire with White Stripe

2 Purple Wires

Air Cleaner

NOTE: Operating engine with loose or

damaged air cleaner components

could cause premature wear and

failure. Replace all bent or damaged

components.

NOTE: Paper element cannot be blown out

with compressed air.

Low-Proﬁ le

Loosen knob and remove air cleaner cover.

Precleaner:

1. Remove precleaner from paper element.

2. Replace or wash precleaner in warm water

with detergent. Rinse and allow to air dry.

3. Saturate precleaner with new engine oil;

squeeze out excess oil.

4. Reinstall precleaner over paper element.

Paper Element:

1. Clean area around element. Remove wing

nut, element cover, and paper element with

precleaner.

2. Separate precleaner from element; service

precleaner and replace paper element.

3. Check condition of rubber seal and replace if

necessary.

4. Install new paper element on base; install

precleaner over paper element; reinstall

element cover and secure with wing nut.

Reinstall air cleaner cover and secure with

knob.

Heavy-Duty

1. Unhook retaining clips and remove end

cap(s).

2. Check and clean inlet screen (if equipped).

3. Pull air cleaner element out of housing and

replace. Check condition of inner element;

replace when dirty.

4. Check all parts for wear, cracks, or damage,

and that ejector area is clean.

5. Install new element(s).

24 590 28 Rev. --

6. Reinstall end cap(s) with dust ejector valve/

Ensure both ends of breather tube are properly

connected.

Fuse Rating

10-amp Fuse

1. Clean ﬁ ns with a brush or compressed air.

2. Remove two screws securing oil cooler, and

10-amp Fuse

3. Reinstall oil cooler.

30-amp Fuse

Proper cooling is essential. To prevent over

heating, clean screens, cooling ﬁ ns, and other

external surfaces of engine. Avoid spraying

water at wiring harness or any electrical

components. See Maintenance Schedule.

We recommend that you use a Kohler

authorized dealer for all maintenance,

service, and replacement parts for engine.

To ﬁ nd a Kohler authorized dealer visit

KohlerEngines.com or call 1-800-544-2444

(U.S. and Canada).

If engine will be out of service for 2 months or

more follow procedure below.

1. Add Kohler PRO Series fuel treatment or

2. Change oil while engine is still warm from

3. Disconnect negative (-) battery cable.

4. Store engine in a clean, dry place.

KohlerEngines.com

screen down; secure with retaining clips.

Breather Tube

Oil Cooler (if equipped)

tilt to clean back side.

Air Cooling

Hot Parts can cause severe

burns.

Do not touch engine while

operating or just after stopping.

Never operate engine with heat shields or

guards removed.

Repairs/Service Parts

Storage

equivalent to fuel tank. Run engine 2-3

minutes to get stabilized fuel into fuel system

(failures due to untreated fuel are not

warrantable).

operation. Remove spark plug(s) and pour

about 1 oz. of engine oil into cylinder(s).

Replace spark plug(s) and crank engine

slowly to distribute oil.

WARNING