Kohler Command Pro EFI ECH980 Panduan Pemilik - Halaman 7
Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Mesin Kohler Command Pro EFI ECH980. Kohler Command Pro EFI ECH980 8 halaman.
Juga untuk Kohler Command Pro EFI ECH980: Panduan Pemilik (8 halaman)
Halaman Cetak
Electronic Fuel Injection (EFI) System
EFI is an electronically-controlled fuel
management system which is monitored by an
Electronic Control Unit (ECU). A Malfunction
Indicator Light (MIL) will illuminate if problems
or faults are detected. Servicing by a Kohler
authorized dealer is necessary.
Fuel System Components
High pressure components inside fuel pump
module are not serviceable. Engines are
equipped with a special EFI fuel fi lter. See
Maintenance Schedule.
Fuse Replacement
These engines have three (3) blade type
automotive fuses. Engines equipped with a
high output charging system, will have one (1)
60-amp large blade type automotive fuse, in
addition to the three (3) blade type automotive
fuses. However, the 30-amp fuse is then non-
functional, as the 30-amp charging system
circuit has been disabled.
Replacement fuses must have same rating as
blown fuse. Use fuse chart below to determine
correct fuse.
Wire Color
2 Solid Red Wires
1 Red Wire with Black Stripe
1 Red Wire with White Stripe
2 Purple Wires
High Output Charging System adds
In separate wiring harness;
when OEM supplied, refer to
your equipment manual for
fuse detail.
Air Cleaner
NOTE: Operating engine with loose or
damaged air cleaner components
could cause premature wear and
failure. Replace all bent or damaged
components.
NOTE: Paper element cannot be blown out
with compressed air.
Low-Profi le
Loosen knobs and remove air cleaner cover.
Precleaner:
1. Remove precleaner from paper element.
2. Replace or wash precleaner in warm water
with detergent. Rinse and allow to air dry.
3. Saturate precleaner with new engine oil;
squeeze out excess oil.
4. Reinstall precleaner over paper element.
Paper Element:
1. Remove paper element with precleaner.
2. Separate precleaner from element; service
precleaner and replace paper element.
62 590 18 Rev. D
3. Install new paper element on base; install
Reinstall air cleaner cover and secure with
knobs.
Heavy-Duty
1. Unhook retaining clips and remove end
2. Check and clean inlet screen (if equipped).
3. Pull air cleaner element out of housing and
4. Check all parts for wear, cracks, or damage,
5. Install new element(s).
6. Reinstall end cap(s) with dust ejector valve/
Ensure both ends of breather tube are properly
connected.
NOTE: When oil cooler is remote mounted in
Fuse Rating
10-amp Fuse
1. Clean fi ns with a brush or compressed air.
2. Remove two screws securing oil cooler, and
10-amp Fuse
3. Reinstall oil cooler.
30-amp Fuse
Kohler
60-amp Fuse
Proper cooling is essential. To prevent over
heating, clean screens, cooling fi ns, and
other external surfaces of engine. Inspect for
any debris visible through fl ywheel cooling
holes (if equipped) and clean as necessary.
Avoid spraying water at wiring harness or
any electrical components. See Maintenance
Schedule.
We recommend that you use a Kohler
authorized dealer for all maintenance, service,
and engine parts. To fi nd a Kohler authorized
dealer visit KohlerEngines.com or call 1-800-
544-2444 (U.S. and Canada).
KohlerEngines.com
precleaner over paper element.
cap(s).
replace. Check condition of inner element;
replace when dirty.
and that ejector area is clean.
screen down; secure with retaining clips.
Breather Tube
Oil Cooler
application and supplied by OEM, refer
to your equipment manual for cleaning
detail.
tilt to clean back side.
Air Cooling
Hot Parts can cause severe
burns.
Do not touch engine while
operating or just after stopping.
Never operate engine with heat shields or
guards removed.
Repairs/Service Parts
WARNING
EN
7