Kohler Courage SV530 Panduan Pemilik - Halaman 11

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Mesin Kohler Courage SV530. Kohler Courage SV530 17 halaman. Vertical shaft
Juga untuk Kohler Courage SV530: Panduan Pemilik (17 halaman), Panduan Pemilik (17 halaman), Panduan Pemilik (8 halaman), Panduan Pemilik (48 halaman)

Halaman Cetak

Figure11.

installing Air Cleaner Element.

Due to the deep recess around the spark plug,

blowing out the cavity with compressed air is

usually the most effective method for cleaning.

The spark plug is most accessible when the

blower housing is removed for cleaning.

Remove the plug and check its condition. Replace

the plug if worn or reuse is questionable.

NOTE:

Do not clean the spark plug in a machine

using abrasive grit. Some grit could

remain in the spark plug and enter the

engine causing extensive wear and

damage.

Clean Air Intake/Cooling

Areas

To ensure proper cooling, make sure the grass screen,

cooling fins, and other external surfaces of the engine

are kept clean at all times,

Annually

or every 100 hours of operation (more often

under extremely dusty, dirty conditions), remove

the blower housing and any other cooling shrouds.

Clean the cooling fins and external surfaces as

necessary. Make sure the cooling shrouds are

reinstalled. Torque the blower housing screws to

7.5 N.m (65 in. lb.).

NOTE:

Operating the engine with a blocked grass

screen, dirty or plugged cooling fins, and/or

cooling shrouds removed, will cause engine

damage due to overheating.

Ignition

System

This engine is equipped with a dependable electronic

CD ignition system. Other than periodically checking/

replacing the spark plug, no maintenance, timing, or

adjustments are necessary or possible with this

system.

In the event starting problems should occur which are

not corrected by replacing the spark plug, see your

Kohler Engine Service Dealer for trouble analysis.

3. Check the gap using a wire feeler gauge. Adjust

the gap by carefully bending the ground electrode.

See Figure 12. Gap plugs to 0.76 mm (0.030 in.).

4. Reinstall the spark plug into the cylinder head.

Torque the spark plug to 24-30 N.m (18-22 ft. lb.).

5. Reconnect the spark plug lead and reinstall the

blower housing, if removed previously. Torque the

blower housing screws to 7.5 N.m (65 in. lb.).

Wire Gauge

Spark Plug

0.76 mm

Ground

(0.030 in. )

Electrode

Gap

Figure 12. Servicing

Spark Plug.

Battery

Charging

Check

Spark

Plug

Every 2 years or 200 hours of operation, remove the

spark plug, check condition, and reset the gap or

replace with a new plug as necessary. The standard

spark plug is a Champion _ RCI2YC (Kohler Part No.

12 132 02-S). If the engine is RFI compliant, a

Champion _> QC12YC (Kohler Part No. 20 132 02-S)is

used. Equivalent alternate brand plugs can also be

used. Spark plug replacement is recommended

at 500

hours.

1. Before removing the spark plug, clean the area

around the base of the plug to keep dirt and debris

out of the engine.

WARNING:

Explosive

Gas!

Batteries produce explosive hydrogen gas while being

charged. Toprevent a fire or explosion, charge batteries

only in weft ventilated areas. Keep sparks, open flames,

and other sources of ignition away from the battery at all

times. Keep batteries out of the reach of children.

Remove all jewelry when servicing batteries.

Before disconnecting the negative (-) ground cable,

make sure all switches are OFF. If ON, a spark will

occur at the ground cable terminal which could cause

an explosion ff hydrogen gas or gasoline vapors are

present.