Avocent Emerge MPX1500 Panduan Instalasi Cepat
Jelajahi secara online atau unduh pdf Panduan Instalasi Cepat untuk Pemanjang Avocent Emerge MPX1500. Avocent Emerge MPX1500 2 halaman. Multipoint high-definition (hd) wired/wireless extender system
Juga untuk Avocent Emerge MPX1500: Spesifikasi Teknis (2 halaman), Panduan Instalasi Cepat (2 halaman), Panduan Instalasi Cepat (1 halaman), Brosur (2 halaman), Brosur (8 halaman), Spesifikasi (2 halaman)
Halaman Cetak
QUICK INSTALLATION GUIDE
For manual downloads, visit:
www.avocent.com/manuals
The following instructions will help you
install your extender system. For more
detailed instructions, including wired
installations and firmware updates, refer to
the installer/user guide.
Should you require further assistance,
please contact Avocent Technical Support.
IMPORTANT SAFETY INSTRUCTIONS
•
Do not use this apparatus near water.
•
Clean with dry cloth only.
•
Do not block ventilation openings.
•
Do not install near any heat source.
•
Do not defeat the safety purpose of the
polarized or grounding-type plug.
•
Protect the power cord from being walked
on or pinched.
•
Only use attachments/accessories
specified by the manufacturer.
•
Unplug this apparatus during lightning storms
or when unused for long periods of time.
Overview
The Avocent Emerge MPX 1500 HD extender
system allows A/V professionals to deliver IP-
based audio and video extension solutions for
large-scale venues involving multiple floors or
buildings. Combining Avocent IP-wired/wireless
MPX 1500 HD transmitters and receivers,
the solution extends audio, video, serial and
IR signals from a source device to widely
distributed display devices. For more information,
refer to the Emerge MPX Extender System
Installer/User Guide.
1
Preparing to use the extender
system
Place your MPX transmitter and receivers at least
three feet apart on a stable work surface and
attach the antennas. If your installation includes
receivers that will have a wired IP connection,
connect the L2 LAN port of the transmitter to
To Contact Avocent Technical Support: Visit www.avocent.com
Avocent, the Avocent logo, and Emerge are registered trademarks of Avocent Corporation or its affiliates in the U.S. and other countries. All other marks are the property of their respective owners. ©2010 Avocent Corporation.
Emerge
MPX 1500
Multipoint High-Definition (HD) Wired/Wireless Extender System
®
Emerge MPX 1500 Extender System Configuration
Video
Source
the L1 LAN port, indicated by the LAN symbol,
on each receiver. Turn on the units and wait for
transmitter initialization to complete. The two
green LEDs will light up alternately and the other
LEDs will turn off.
Configuring the transmitter
2
Connect a browser client to the transmitter's L1
LAN connector and launch a browser session
using the IP address 192.168.1.1 with a subnet
mask of 255.255.255.0.
•
At the login prompt, leave the username blank
and enter Admin (case sensitive) as the
password.
•
When prompted, select the appropriate
country code.
•
Select
Source Device Settings and configure
the input video mode for the transmitter. See
the Emerge MPX Extender System Installer/
User Guide for more information.
•
Select
Change Password to update the
system password.
•
Select
System Settings to enter a device
name.
•
If your installation includes wired receivers,
select Media LAN Settings and enable Wired
Connection in the Basic LAN Settings tab.
MPX
MPX
Receiver
Transmitter
LAN
Up to 8 display configuration
3
Turn on your receivers. Wait for them to initialize
and bind to the transmitter. The two green LEDs
will cease to alternate.
•
Select the Bindings page on the transmitter's
web interface and verify that all active
receivers are listed (by MAC address) in the
Detected Receivers list.
•
Select the Add to Configured Receivers
checkbox next to each receiver then apply the
changes.
•
Assign one unit as the primary receiver for
exchange of IR, serial and EDID data and
apply the change.
•
If all receivers are bound, you may disable
the transmitter from automatically binding
additional receivers.
4
In the Active Receivers list (lower left of the
transmitter's web interface), click the MAC
address of the first active receiver to access its
web interface.
•
Select
the output video mode of the receiver.
Emerge MPX Extender System Installer/User
Guide for more information.
•
Select
the receiver.
To configure the receiver to ignore all but the
Video
Display
Using explicit bindings (optional)
Configuring the receiver
Display Device Settings to configure
System Settings and enter a name for
See the
590-877-501C