Avocent DSI5100 Panduan Instalasi Cepat
Jelajahi secara online atau unduh pdf Panduan Instalasi Cepat untuk Perangkat Keras Jaringan Avocent DSI5100. Avocent DSI5100 2 halaman. Ipmi proxy appliance
Halaman Cetak
The following instructions will allow you
to set up your DSI5100 Intelligent
Platform Management Interface (IPMI)
proxy appliance easily.
Setting up the DSI5100 Appliance
Remove the DSI5100 IPMI proxy appliance from the
packaging material and place it in the chosen location.
1
Powering the DSI5100 IPMI proxy appliance
Locate the power cord that came with the DSI5100 IPMI proxy
appliance. Plug one end into the power socket on the rear of
the DSI5100 IPMI proxy appliance. Plug the other end into an
appropriate AC wall outlet.
2
Connecting a terminal (optional)
Connect a terminal or PC running terminal emulation
software to the serial port on the back panel of the DSI5100
IPMI proxy appliance using the supplied null modem cable.
Set the terminal to 38.4K, 8 bits, 1 stop bit, no parity and no
flow control.
3
Connecting to the LAN
Using UTP cable, connect the network port on the back of the
DSI5100 IPMI proxy appliance to your LAN.
Launching the DSView
software and adding the
®
DSI5100 IPMI proxy appliance
Using the DSView management software from a DSView
software Client, add the DSI5100 IPMI proxy appliance to the
DSView management system with the Add Unit Wizard. See
the DSView Installer/User Guide for detailed information.
NOTE: A DSI5100 IPMI proxy appliance may only be
added and operated in Secure mode within a DSView
software system.
Adding the servers to monitor
Using the DSView management software, add the target
devices you wish to monitor with the Add IPMI BMC Wizard.
See the DSView Installer/User Guide for detailed information.
NOTE: The DSI5100 IPMI proxy appliance supports
IPMI 1.5 compatible target devices.
Monitoring the IPMI servers
Use the IPMI Viewer window to monitor IPMI appliance target
devices. See the DSView Installer/User Guide for more information.
Using DSI5100 IPMI proxy appliance commands
During normal use with DSView software, you should have no
need to access the DSI5100 IPMI proxy appliance command
interface. However, the DSI5100 IPMI proxy appliance
supports five commands which can be entered by logging into
the DSI5100 using a terminal or terminal emulation program.
To Contact Avocent Technical Support
Avocent, the Avocent logo, The Power of Being There and DSView are registered trademarks of Avocent Corporation. All other marks are the property of their respective owners. © 2005 Avocent Corporation. All rights reserved.
Quick Installation Guide
DSI5100
IPMI Proxy Appliance
To connect a DSI5100 IPMI proxy appliance
1
Connecting power to
the appliance
To use a terminal or terminal emulation program:
1. After mounting the appliance, connect a terminal
or PC running terminal emulation software to the serial
port on the back panel of the DSI5100 appliance using
the supplied null modem cable. Configure your terminal or
terminal emulation program as follows:
Baud rate - 38.4K
Bits per character - 8 bits
Parity - None
Stop bits - 1 stop bit
Flow control - None
2. On the Terminal screen, enter root as the default
username and root as the default password.
NOTE: The DSI5100 appliance can also be accessed using a
standard SSH client.
Changing the DSI5100 network configuration
setip
The setip command configures the network configuration of
the DSI5100 IPMI proxy appliance. The following setup options
display, as shown in Figure 1:
setip DHCP
setip IP ipaddress netmask [gateway]
NOTE: Gateway is in brackets on the screen because it
is optional.
NOTE: Using DHCP enables you to obtain IP address and
network configuration. For the DHCP server reservation, locate
the MAC address on the bottom of the DSI5100 appliance or
use the ifconfig command on the following page.
CALL (888) 793-8763
VISIT www.avocent.com/support
Network
3
DSView Software
Connecting to a LAN
TX
LINK
DOWNLOAD Check out the latest software from our web site at: www.avocent.com
Sensor Data
IPMI Capable
Server
DSI Appliance
RESET
PWR
CF
2
Connecting a terminal
(optional)
Figure 1: IP Parameter Setup
To manually change the DSI5100 appliance
network configurations:
1. Reboot the DSI5100 appliance by entering reboot
on the Terminal screen.
2. After you have rebooted the appliance, at the
login prompt, enter root as the username and root as
the password.
3. Modify DSI5100 appliance configuration settings
using the setip command.
4. Verify the new IP parameters by entering ifconfig.
The IP parameters are displayed as shown in Figure 2.
Figure 2: IP Parameter Summary
5. Log out of the Terminal screen by entering exit.
590-461-501C