EnStar Split Wall Mounting Type Panduan Instalasi

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Pendingin Udara EnStar Split Wall Mounting Type. EnStar Split Wall Mounting Type 2 halaman.

Halaman Cetak

INSTALLATION MANUAL FOR ROOM

AIR CONDITIONER

(Split Wall Mounting Type)

For correct installation, read this manual before starting installation. Please save this manual in a safe place.

Only trained and qualified service personnel should install, repair or service air conditioning equipment.

Users should not install the air conditioner by themselves.

Pictures in this manual may be slightly different from the air conditioner you purchased. These pictures

are only sketches.

INSTALLATION PRECAUTION

Installation in the following places may cause trouble. If it is unavoidable to use in such places, please

consult with the dealer:

A place full of machine oil.

A saline place such as coast.

A place full of sulfide g s such as hot-spring resort.

Places where there are high frequency machines such as wireless installation, welding machine, and

medical facility.

A place of special environmental conditions.

Indoor Unit

A place where is no obstacle near the inlet and

outlet area.

place which can bear the weight of the indoor unit.

place which provides the spaces around the

indoor unit as required right in the diagram.

A place 1m or more from TV, radio instrument, in

the center of the room is perfect.

A place which is far from heat, steam and

inflammable gas.

Install the indoor unit on the wall where the height

from the floors more than 2.3 meters.

NOTE:

The appliance shall not be installed in the laundry. All the connection must be in accordance with

national regulations.

For detailed installation acceptance, please refer to your contract with the power supplier if restrictions

do apply for products like washing machines, air conditioners or electrical ovens.

For power details of the air conditioner, refer to the rating plate of the product. Contact your local dealer if

you have any questions.

1. Cutting A Hole and Mounting Installation Plate

Installation Plate and Its Measures (Unit: mm)

Above 150 from

the ceiling

1250

178

815

Above 120 from

the wall

Pipe hole

1. Fix the installation plate.

Install the installation plate horizontally on structural

members in the wall with the spaces provided around the

plate.

In case of block, brick, concrete or similar type walls,

make 5mm dia, holes in the wall. Insert clip anchors for

appropriate mounting screws.

Fix the installation plate on the wall.

3. Indoor unit Installation

Pass the piping through the

Upper hook

hole in the wall.

Put the upper claw at the back

Low hook

of the indoor unit on the upper

hook of the installation plate,

Move the indoor unit from side

to side to see that it is securely

hooked.

Push the lower part of the

indoor unit up on the wall.

Piping can easily be made by

lifting the indoor unit with a

Cushioning material

cushioning material at the

remote controller holder side

between the indoor unit and the

wall.

Outdoor Unit

A place, which is convenient to installation and

not exposed to a strong wind.

A place can bear the weight of the outdoor unit

and where the outdoor unit can be held in the

horizontal position.

A place where the operation noise and disc-

harge air do not disturb you neighbor.

A place free of a leakage of combustible gases.

An allowable head level at the connective

piping is less than 5m and length of the

connective piping is up less than 10m.

A place, which provides the spaces around the

outdoor unit as required right in the diagram.

Unavailable to children.

INDOOR UNIT INSTALLATION

Hooked Part Hooker Part

257

Above 120 from

the wall

2. Cutting a hole.

Determine the pipe hole position

using the installation plate, and drill

the pipe hole (

95mm

) so it slants

slightly downward.

Always use a piping hole cap when

piercing a wall, made of metal lath,

wire lath or metal plate.

4. Electrical Work

Prepare the power source for exclusive with the air conditioner.

The supply voltage must be the same as the rated voltage of the

air conditioner.

Power Supply

Model

220-230V~

60Hz

24000Btu/h

220-240V~

50Hz

24000Btu/h

NOTE:

A disconnection device having an air gap contact separation at least

3mm in all conductors should be incorporated in the fixed wiring

according to the National Wiring Regulation.

Caution

Perform the wiring with sufficient capacity.

Installation places legally require a short circuit isolator to be

attached to prevent electrical shock.

Do not extend the power cable code by cutting.

The plug of the air conditioner takes a grounding leg, so clients

should use a grounding socket so that the air conditioner can be

grounded efficiently.

Installation Parts

Part

Name of part

No.

Installation plate

Clip anchor

Mounting screw A ST3.9x25-C-H

Remote controller

Remote controller holder

Mounting screw B ST2.9x10-C-H

6.35( 24000Btu/h)

Liquid side

Refrigerant

9.53( 24000Btu/h)

pipe

12.7( 24000Btu/h)

Gas side

16( 24000Btu/h)

Seal

Drain elbow

Caution

The outdoor unit should not be exposed

to strong wind.

Fix the outdoor unit with

10 anchor

bolts.

air inlet

air outlet

Model

24000Btu/h

560

335

24000Btu/h

590

333

If need suspending installation, consults

the corresponding requirement.

2. Connective Pipe and Drainage Installation

1. Drainage

Run the drain hose sloping downward. Do not

install the drain hose as illustrated below.

Do not form a rise.

Do not put the drain

end into water.

When connecting extension drain hose,

insulate the connecting part of extension

drain hose with a shield pipe.

Wall

Shield pipe

Extension drainhose

Drain hose

Inside the room

Lift the panel, loose the screw then open the Electric Box Cover.

Connect the wires to the terminals on the control board indivi-

dually according to the outdoor unit connection.

AWG(MIN.)

Input Rated Amp

Wrap those cables not connected with terminals with insulation

Power Supply

Connecting

(Switch/Fuse)

cord

tapes, so that they will not touch any electrical components.

cable

32/20A

32/25A

Q'ty

Cautions on remote controller installation

Before installation, operate the remote

controller to determine its location in a

reception range.

Keep the remote controller at least 1m

apart from the nearest TV set or stereo

equipment.

Do not install the remote controller in a

place exposed to direct sunlight or close

to a heating source, such as a stove.

Note that the positive and negative

poles are right positions when loading

batteries.

Remote

Controller

Remote controller

holder

ST2.9X10-C-H

Mounting screw B

Loop the connective

Remove the water receiver first

cable.

before connecting the pipes.

NOTICE:

There should be at least two of

the A, B, C direction are free from

blocking.

2. Connective pipe

For the left-hand and rear-left-hand piping,

install the piping as shown. Bend the conne-

ctive pipe to be laid at 43mm height or less

from the wall.

Indoor unit outline

Connective pipe

Fix the end of the connective pipe.

Caution

Connect the indoor unit first then the

outdoor unit.

Bend and arrange the pipe carefully.

Insulate both of the auxiliary piping.

Drainage can not annoy your neighbor.

5. Connecting Cables

Panel

Terminal block

1 2(N) S

Code wire

Terminal block of indoor unit

To outdoor unit