Avtron AV685 Petunjuk - Halaman 2
Jelajahi secara online atau unduh pdf Petunjuk untuk Konverter Media Avtron AV685. Avtron AV685 4 halaman.
Halaman Cetak
INSTALLATION
MACHINE SHAFT PREPARATION
Preparing the machine shaft prior to Pulse Generator instal-
lation is essential in providing an adequate barrier against
environ mental contamination. In some cases, a separate stub
shaft (1.125" D x 4.5" long) will be installed on the motor. To
prepare the machine shaft that the M585 is to be installed on,
conduct the following procedures (see figures):
1.
Remove from the M585 the four
screws which hold the end cap on the cover plate.
2.
Remove the end cap, O-Ring, and wave spring, noting
the location of each to assist in reassembly.
SPANNER WRENCHES MUST BE USED DURING THE
FOLLOWING PROCEDURES. Using a substitute can distort
the 1
" nut and damage the unit. Do not try to remove the
⁄
3
4
2
⁄
" bearing locknut at any time. This locknut is factory adjusted
1
2
for optimum M585 performance.
Two spanner wrenches, which are required for M585 installa-
tion, accommodate the 1
⁄
3
3.
Holding the 2
" bearing locknut, remove the 1
⁄
1
2
ter clamping nut and slide out the internal compression sleeve.
4.
Verify that the compression sleeve can be installed by
hand on the shaft where the unit is to be installed. File any burrs
that obstruct sleeve installation and lightly oil the shaft.
5.
If a keyway or flat exists on the shaft, provide a sealing
medium or true shaft back to round using metal putty or equal.
6.
Return the compression sleeve to the M585 hub.
7.
Thread the 1
" clamping nut onto the M585 by hand until
⁄
3
4
resistance is felt. DO NOT TIGHTEN AT THIS TIME.
PULSE GENERATOR INSTALLATION
Installing the M585 and Anti-Rotation Arm:
1.
The free end of the Anti-Rotation Arm must be secured
by the customer to a stationary member such as the floor or
machine frame. Refer to "Anti-Rotation Arm Mounting Guide-
lines" on the last page
for
general
re quire -
ments.
2.
Based on the lo-
cation of the sta tionary
point and the guidelines
on page 4, attach the
" thick mounting board
⁄
1
4
pro vided to one of five
places on the M585.
Use two
⁄
-20 UNC by
1
4
" long machine screws
⁄
3
4
provided.
3.
Ensure that the
machine shaft is lightly
oiled. A packet of sili-
cone grease is provided
to lubricate the following
shaft seals: First, ALL
-20 UNC machine
⁄
1
4
CAUTION
NOTE
" and 2
" nuts found under the cap.
⁄
1
4
2
M585 types have an O-ring inside their hollow shafts at the mo-
tor end. In addition, in THRU SHAFT types, the clamping nut
has an O-ring on the inside, plus the outside of the clamping nut
requires lubrication for the radial lip seal per step 8b. Slide the
M585 onto the machine shaft, mounting board first. Ideally, the
M585 housing will be
ing, but this may vary depending on the machine profile and the
anti-rotation arm clearance requirements. Consider shaft end
float when positioning the M585.
4a. FOR STUB SHAFT APPLICATIONS, place the M585
3
" to 4" onto the shaft. The end of the machine shaft must ex-
⁄
1
4
tend completely through the M585 compression sleeve and be
approximately flush with the end of the 1
4b. FOR THRU SHAFT APPLICATIONS, position the M585
as required.
5.
Attach free end of the Anti-Rotation Arm to the
" mounting board using the shoulder bolt provided.
⁄
1
4
6.
Remove 1
to the threads. (Locktite grade 242, supplied, should be used in
most applications.)
Where thread locker has been used, additional force is required
for M585 removal.
" diame-
⁄
3
4
7.
Replace 1
than or equal to 0.09", as shown in CLAMPING NUT sketch
(approx. 15-20 ft-lbs), holding the 2
Spanner wrenches are required for this operation.
8a. FOR STUB SHAFT INSTALLATIONS, replace the end
cap with the wave spring (loading spring) against the bearing
and the O-ring located in the cap groove. Secure the end cap
with the four
Apply the supplied grade 242 Locktite to the screws when as-
sembling.
8b. FOR THRU SHAFT APPLICATIONS, prior to replac-
ing the end cap per step 8a, apply a small amount of silicone
grease (provided) to the seal surface on the 1
The radial lip seal in the end cap will seal on this surface.
" to 1" from the motor or machine hous-
⁄
1
2
" clamping nut and apply liquid thread locker
⁄
3
4
NOTE
" clamping nut and tighten so the gap is less
⁄
3
4
⁄
" bearing locknut in place.
1
2
⁄
-20 UNC machine screws previously removed.
1
4
" clamping nut.
⁄
3
4
" clamping nut.
⁄
3
4