Dell wyse V00 Panduan Memulai Cepat - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Server Dell wyse V00. Dell wyse V00 6 halaman. V class

Halaman Cetak

English -

Thin Client Installation

Refer to the figures and proceed as follows:

Caution Statements

Improper connection, mounting, or use of this product could result

in component failure or undesired interference. Read the following

caution statements before setting up and operating the thin client.

Setup

•

Do not connect to AC power until all other connections

(including the power adapter) are made. Connecting or

disconnecting components or equipment on the back panel

when the thin client is receiving AC power can cause power

surges and damage the device.

•

Do not force a connector into its socket. If any undue resistance

is encountered, ensure that the connector is correctly oriented

to the receptacle.

Orientation and Venting

•

Mount the thin client only as shown or in accordance with the

instructions provided with Wyse-approved mounting accessory

kits. Improper orientation could inhibit the dissipation of heat

from the device and damage it.

•

Allow sufficient space around the thin client for ventilation; do

not place the device in any enclosure that restricts airflow

around the device; do not place any objects on the device or

block the vent holes under the device. Find environmental

operating specifications in the thin client's datasheet located at:

http://www.wyse.com/products/winterm

•

For wireless usage and requirements, refer to the regulatory

notices in the thin client's documentation.

Power Sources

•

To ensure regulatory compliance, use only the power adapter

included in the shipping carton, or a Wyse-approved equivalent,

with the thin client. Refer to the regulatory notices in the thin

client's documentation (for Products V00 and VR0, refer to any

Model VX0 thin client's regulatory notices).

•

Accidental loss of power can damage the thin client. Avoid

connecting it to any power outlet which can be accidentally

switched off. Do not hard reset the thin client by holding down

the power button during normal operation.

•

When turning off the thin client, be sure to perform a complete

shutdown (via the user interface or a light press on the power

button). Do not disconnect the AC power cord, DC power cord,

or shut off power at a circuit breaker (including power strips),

etc., to turn off the device.

•

Surge protectors for electrical devices are recommended in

areas of lightning. However, when lightning is occurring, your

equipment should be properly shut down and unplugged from

AC power until the storm has passed.

•

Be very careful to not interrupt power while the thin client is

downloading a software update.

Connect

Refer to the figures and proceed as follows:

1. Place the thin client on a desk, or use a Wyse-approved

mounting accessory kit.

2. Make all desired connections (video display and keyboard

with mouse are required). Connection to a 10/100 BaseT

Ethernet network is required unless an optional WiFi network

adapter is used for wireless connection to a network.

Additional connections of peripheral devices may be made to

the other ports.

3. Connect the power adapter to the thin client power input

before connecting to a 100-240V AC, 50-60 Hz electrical

outlet. Wait until the initialization sequence is completed (the

amber light on the power button will go off), and then press the

power button on the thin client to apply power.

Configure

Products V30, V50, and V90 - After power-on, the thin client

initially goes through several boot sequence procedures before

the operating system loads. Information about setting up your

server environment is available in the thin client's documentation.

Products V00 and VR0 - Wyse Streaming Manager software is

required; no other configuration is needed. Information about

setting up your server environment is available in the Wyse

Streaming Manager documentation.

Need more information?

Wyse Reference Guides (Products V30, V50, and V90) -

User, Administrator, and related documentation is available at:

http://www.wyse.com/manuals

Wyse-Approved Mounting Accessory Kits - Information about

approved mounting accessory kit options is available at:

http://www.wyse.com/products/accessories/mounting.asp

Wyse Service and Support Web Site - Upgrade software

images for installation on your FTP file server are available at:

http://www.wyse.com/serviceandsupport/support/askwyse.asp

Wyse Device Manager - Information about Wyse remote

management software is available at:

http://www.wyse.com/bundle

Wyse Streaming Manager - Information about Wyse Streaming

Manager software is available at:

http://www.wyse.com/products/software/streamingmanager

Wyse and the Environment - Information about Wyse

compliance with the Waste Electrical and Electronic Equipment

(WEEE) is available at:

http://www.wyse.com/about/environmental

Wyse Warranty Registration - Wyse's warranty registration*

process is available at:

http://www.wyse.com/serviceandsupport/register.asp

*The standard warranty is three years from the date of purchase.