Dell POWERCONNECT J SERIES Panduan Memulai Cepat - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Beralih Dell POWERCONNECT J SERIES. Dell POWERCONNECT J SERIES 24 halaman.

Halaman Cetak

Dell POWERCONNECT J SERIES Panduan Memulai Cepat

Part 5: Perform Initial Configuration

NOTE: To obtain an IP address dynamically, you must enable a DHCP client on the

management PC you connect to the switch.

NOTE: Read the following steps before you begin the configuration. Complete the initial

configuration using EZSetup within 10 minutes. The LCD panel displays a count-down

timer when the switch is in initial setup mode. The switch exits EZSetup after 10 minutes

and reverts to the factory configuration, and the PC loses connectivity to the switch.

1. Transition the switch into initial setup mode using the Menu and Enter buttons to the

right of the LCD panel. To do this:

− Press Menu until you see

MAINTENANCE MENU

− Press Menu until you see

ENTER EZSetup

If EZSetup does not appear as an option in the menu, select Factory Default to

return the switch to the factory default configuration. EZSetup is displayed in the

menu only when the switch is set to the factory default configuration.

− Press Enter to confirm setup and continue with EZSetup.

2. Connect the Ethernet cable from the Ethernet port on the PC to port

the front panel of the switch.

The

interface is now configured as the DHCP server with the default IP

ge-0/0/0

address,

. The switch can assign an IP address to the management PC

192.168.1.1

in the IP address range

192.168.1.2

3. From the PC, open a Web browser, type

press the Enter key.

4. On the J-Web Login page, enter

root

blank, and click Login.

5. On the Introduction page, click Next.

6. On the Basic Settings page, enter the hostname, enter and reenter a password,

specify the time zone, and synchronize the switch date and time settings with the

management PC or set them manually.

7. Click Next.

8. Use the Management Options page to select the management scenario:

− In-band Management—Use VLAN 'default' for management

Select this option to configure all data interfaces as members of the default VLAN.

Click Next. Specify the management IP address and the default gateway.

− In-band Management—Create new VLAN for management

Select this option to create a management VLAN. Click Next. Specify the VLAN

name, VLAN ID, member interfaces, and management IP address and default

gateway for the new VLAN.

− Out-of-band Management—Configure management port

Select this option to configure only the management interface. Click Next. Specify

the IP address and default gateway for the management interface.

9. Click Next.

10. On the Manage Access page, you may select options to enable Telnet, SSH, and

SNMP services. For SNMP, you can configure the read community, location, and

contact.

Information in this document is subject to change without notice. Trademarks used in this text: Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc. Juniper Networks® and Junos® are registered trademarks of

Juniper Networks, Inc. in the United States and other countries. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners. Juniper Networks assumes no

responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice. Products made or sold by Juniper Networks or components thereof

might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579,

6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.

Copyright © 2010, Juniper Networks, Inc. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Juniper Networks is strictly forbidden. Printed in USA.

Juniper Networks Part Number: 530-06262. Revision 01, 15 August 2010

. Then press Enter.

(

ge-0/0/0

through

192.168.1.253

in the address field, and

http://192.168.1.1

as the username, leave the password field

11. Click Next. The Summary page displays the settings you have selected.

12. Click Finish. The configuration is committed as the active switch configuration. You

can now log in with the CLI or the J-Web interface to continue configuring the switch.

NOTE: After the configuration is committed, the connectivity between the PC and the

switch might be lost. To reconnect, release and renew the IP address by executing the

appropriate commands on the PC or by removing and reinserting the Ethernet cable.

Safety Warnings Summary

This is a summary of safety warnings. For a complete list of warnings, including

translations, see the see the PowerConnect J-EX4200 switch documentation at

http://www.suppport.dell.com/manuals

WARNING: Failure to observe these safety warnings can result in personal injury

or death.

Permit only trained and qualified personnel to install or replace switch components.

Perform only the procedures described in this quick start and the J-EX4200 switch

) on

documentation. Only authorized service personnel must perform other services.

Before installing the switch, read the planning instructions in the J-EX4200 switch

documentation to make sure that the site meets power, environmental, and clearance

requirements for the switch.

Before connecting the switch to a power source, read the installation instructions in the

J-EX4200 switch documentation.

A fully loaded J-EX4200 switch weighs approximately 22 lb (10 kg). Manually installing

the switch in a rack requires one person to lift the switch and a second person to install

mounting screws. To prevent injury, keep your back straight and lift with your legs, not

your back.

If the rack has stabilizing devices, install them in the rack before mounting or servicing

the switch in the rack.

Before installing or after removing an electrical component, always place it

component-side up on a flat antistatic surface or in an electrostatic bag.

Do not work on the switch or connect or disconnect cables during electrical storms.

Before working on equipment that is connected to power lines, remove jewelry,

including rings, necklaces, and watches. Metal objects heat up when connected to

power and ground and can cause serious burns or become welded to the terminals.

Power Cable Warning (Japanese)

The power cable is only for this product. Do not use the cable for another product.

Contacting Dell Inc.

For technical support, see

http://www.support.dell.com