AVYCON AVR-HN516P16A Panduan Memulai Cepat

Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Perangkat Keras Jaringan AVYCON AVR-HN516P16A. AVYCON AVR-HN516P16A 2 halaman.

Halaman Cetak

Network Video Recorder

Quick Start Guide

Note: Please read this instruction carefully for correct use of the product and preserve it for reference purposes.

All the examples and pictures used here are for reference only. There may be several technically incorrect

places or printing errors in this manual. The updates will be added into the new version of this manual. The

contents of this manual are subject to change without notice.This device should be operated only from the

type of power source indicatedon the marking label. The voltage of the power must be veriﬁed before using

the same.

1. HDD Installation

This series of the product supports 2 SATA hard drive. Please make

sure that the device is powered off before the installation. The pictures

of the installation are only for reference, please take the real object as

the standard.

1. Loosen the screws to open the cover.

2. Screw the screws into the holes of HDD but

not tighten them.

3. Put the HDDs onto the bottom of the device.

4. Connect the power and data cables.

5. Turn over the machine and secure the HDD

6. Install back the cover and secure it with the

with the screws.

screws.

Tips: Please check the inside structure of the device and make sure the cables connected well

before installing the cover back.

2. Rear Panel Installation

DC48V

PoE Ports

The interfaces of the rear panel are for reference only.

3. Startup & Shutdown

• Startup

1. Connect the monitor and the power.

2. The device will boot and the power indicator will display blue.

3. A wizard window will pop up.

• Shutdown

Click "Start" and then select "Shutdown" icon. This will bring up a

shutdown window. The device will shut down by clicking "OK" button.

Then disconnect the power.

4. Login

The default username is admin and the default password is 123456.

You must conﬁgure the wizard if you start the NVR for the ﬁrst time

and you may change the password when you conﬁgure the wizard for

the ﬁrst time. You can skip the settings of wizard next time. Click

"Start" and select "Login". This will take you to see a login box. Input

default username and password you set and you can see the live

image.

Username

admin

Password

Enter Password

Display Password

Edit Security Question

Network Configuration & Add IP Camera

After you ﬁnish adding IP cameras, you can see the live images

through the monitor of the NVR. The following will mainly

introduce how to add the IP cameras via LAN/WAN.

• LAN

1. Set the network of the NVR. Go to Start → Settings →

Network → TCP/IP. Input IP address, subnet mask, gateway,

etc. If using DHCP, please enable DHCP in both the NVR and

the router.

2. Go to Start → Settings → Network → Port. Input HTTP port

(the default value is 80), server port (the default port is 6036).

AUDIO

3. The internal ethernet port is the port which connects all the PoE

OUT

ports with the NVR system. The PoE ports are available if the

internal ethernet port is online; if it is ofﬂine, all the PoE ports

AUDIO

LAN

VGA

USB

will be unavailable. The IP address and subnet mask of the internal

ethernet port can be changed to make the port in the same

network segment with the IP cameras which directly connect to

Internet

the PoE ports of the NVR.

IP Address Settings

Ethernet Port 1 ( Online )

Obtain an IPv4 address automatically

Address

Subnet Mask

Gateway

MTU

Obtain DNS automatically

Preferred DNS

Alternate DNS

4. Go to Start → Settings → Camera → Add Camera. The NVR

will automatically refresh the cameras searched. The IPC which

supports the Onvif protocol may be added manually. If the IPC

searched is not in the same local network as the NVR, you

should select the device and click

Quickly Add

No.

Selected: 1/3

Remain Bandwidth: 108 / 120 Mb

Cancel

Internal Ethernet Port ( Online )

Obtain an IPv6 address automatically

192 . 168 .

1 .

Address

255 . 255 . 255 . 255

Mask Length

192 . 168 .

1 .

Gateway

1500

Apply

to modify the IP address.

Add Camera

Manually Add

Add Recorder

Subnet Mask

Protocol

Model

Version

Address

Port

Edit

192.168.1.20

255.255.255.0

XXX

3.4.2

192.168.1.38

255.255.255.0

XXX

3.4.2

192.168.2.45

255.255.255.0

XXX

4.0.0.1.beta1

Default Password

Add

Cancel

Edit Camera

Mac Address

CE :98 :23 :75 :35 :22

Address

192 .168 . 1 . 45

Sync to IPC

Subnet Mask

255 . 255 . 255 . 0

Gateway

192 .168 . 1 . 1

Username

admin

Password

Cancel