Dialight ProSite Petunjuk Pemasangan & Pengoperasian - Halaman 3
Jelajahi secara online atau unduh pdf Petunjuk Pemasangan & Pengoperasian untuk Lampu Banjir Dialight ProSite. Dialight ProSite 20 halaman. For cid2/ciid1/ciid2/ciii
Juga untuk Dialight ProSite: Petunjuk Pemasangan & Pengoperasian (18 halaman), Petunjuk Pemasangan & Pengoperasian (9 halaman), Petunjuk Pemasangan & Pengoperasian (8 halaman)
Halaman Cetak
English
WARNING:
To avoid the risk of fire, explosion, or
electric shock, this product should be
installed, inspected, and maintained by
a qualified electrician in accordance
with all applicable electrical rules and
regulations.
Safety Instruction:
To avoid electric shock:
Be certain electrical power is OFF
before and during installation and
maintenance.
Make sure the supply voltage is the
same as the rated luminaire voltage.
The technical data indicated on the
LED luminaires are to be observed.
Changes
of
the
modifications to the LED luminaire are
not permitted.
Observe
the
national/regional
electrical safety rules and regulations
during installation.
The LEDs of this luminaire are not
replaceable; when the LEDs reach
their end of life, the whole luminaire
shall be replaced.
NOTE: Watertight fittings are required to be
used on this luminaire.
Conditions of Use:
Do not open when energized or when
an explosive atmosphere may be
present.
Potential
electrostatic
hazard.
Be
sure
to
instructions. Luminaires should be
cleaned
with
a
damp
periodically.
Equipment Application
This product can be used inside or outside to
illuminate areas in an industrial location.
WARNING: Please ensure the application
structure can handle the weight of the
luminaire. Dialight is not responsible for any
damages to the application structure or the
luminaire when mounted improperly.
Installation
Ensure that the mains voltage supply is
disconnected
before
connecting
luminaire.
Install
the
accordance
with
the
instructions as well as any other applicable
electric codes.
9100FLM000903 REV B
Page 3 of 20
ProSite Floodlight for ATEX/IECEx Zone 2
Technical Data:
Locations:
F*B7**2*D(E/F)***N
Notice for ATEX/IECEx Models:
Ex ec IIC T4 Gc
Ex tb IIIC T110°C Db
ITS-I 22 ATEX 29411X
ITS-I 22 ATEX 294111X
IECEx ETL 22.0001X
Temperature Range:
F1B****(B/C/E/F)******
F2B****(F/H/L)******
F2B****(E/N)******
design
and
Rated Input Voltage:
F*B***(2/8)*******
120-277 VAC 50/60 Hz or 130-250 VDC
Weight:
F1B***********
F2B***********
Impact Rating:
F*B7**********
Cable Entries:
Dimensions:
Always transport and store the equipment in
charging
its original packaging and keep in a dry
read
full
location. When unpacking check for any
cracks or damage in the housing or lens. If in
cloth
doubt, do not install.
When assembling the cable entries for the
mains
manufacturer's specifications for the glands
used. Unused cable entries must be closed
and sealed by a certified blanking plug.
NOTE: The addition of cable glands, dust
caps, electrical plugs, or occupancy sensors
may change the IP rating of this luminaire.
WARNING: Do not over tighten as the
protection rating may be compromised.
Always refer to the gland manufacturer's
data for torque settings.
the
equipment
in
manufacturer's
IP-64 per IEC/EN 60079-0
IP-66/67 per IEC/EN 60529
-40°C to +65°C [-25°F to +149°F]
-40°C to +55°C [-25°F to +131°F]
13,6 kg [29,9 lbs]
24,5 kg [54,1 lbs]
2x M25x1,5
See Technical Diagrams
connection,
always
observe the
Dialight, 1501 Route 34 South, Farmingdale, NJ, USA 07727
Tel: +1 732 919 3119 Fax: +1 732 751 5778
Technical Data:
Power Consumption:
F1B***2B******
F1B***2C******
F1B***2E******
F1B***2F******
F2B***2F******
F2B***2H******
F2B***2L******
F2B***2N******
Mounting the Luminaire
This product can be mounted via bracket. All
mounting options offer 7.5 degrees of
adjustment with angle indication labels
present.
There are 2 bracket models, Forward Throw
and Straight Swivel. See the Technical
Diagrams section for the mounting patterns.
Once mounted, the angle of the luminaire
can be adjusted by loosening the M8 Hex Bolt
on each side of the bracket. When loosening,
do not back bolt out more than 5 full
rotations.
IK-08
When the desired angle has been achieved,
the bolts can be tighten to lock in the angle.
Torque: 20,3 N-m [15 ft-lbs]
WARNING: Do not loosen the Hex Nuts on the
bracket.
Hex Nuts
81 W
124 W
175 W
234 W
200 W
234 W
346 W
484 W
M8 Hex Bolts
www.dialight.com