Miller Solo-Q 2510 Panduan Operator - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Operator untuk Aksesori Kamera Miller Solo-Q 2510. Miller Solo-Q 2510 8 halaman.

Halaman Cetak

ENGLISH

Introduction

Thank you for purchasing the Miller Solo-Q tripod. Solo-Q is a

professional tripod, compatible with industry standard 75 &

100 mm ball levelling pan & tilt heads. Solo-Q is designed to

support camcorders in location and studio production.

The quality of design, manufacture and finishing of the Solo-Q

tripod has proven to deliver strength, lightweight, durability

and versatility. The Carbon Fibre tubing provides optimum

rigidity while the patented Q-lock function significantly reduces

the set-up and pull-down time.

The Q-lock will automatically latch the leg at the end of the

pull-down action, without the need to tighten the leg locks for

transportation. Pressing the Q-lock button, allows the stages

not held by the respective leg lock to slide out. The Q-lock

allows the user to choose their preferred configuration – such

as automatic release of the top stage only when shooting at

medium height or all sections at once to extend the tripod to

its maximum height.

Solo-Q tripod setup

Select rubber foot position for either indoor or outdoor

conditions.

Indoor (hard surfaces): rotate anticlockwise all rubber feet

(check foot is fully down).

Outdoor: rotate clockwise all rubber feet fully to expose spike.

Extend the tripod leg, hold the tripod by the bowl with

legs pointing toward the ground. Working with each leg

individually, check that the desired leg locks are loose, and

then press Q-lock release button to let the legs slide out to the

desired length.

Tighten the leg locks using the markings on the legs as a

guide.

The Solo-Q tripod has three leg angle positions. To change

the leg angle pull up the leg angle adjuster until it locks into a

raised position and push the leg outwards to position 3, then

if required push the leg inwards to positions 2 or 1. The leg

angle adjuster will automatically engage and hold the leg in

that position. To return the leg to a transport position push the

leg inwards.

All stages can be extended when using leg angle position 1,

when using leg angle position 2 only use first stage leg locks to

adjust to desired height and for leg angle position 3 keep tripod

leg fully collapsed for ultra-low ground hugging heights.

Re adjust tripod leg angles and leg lengths if the tripod

is set-up on an uneven surface such that the tripod bowl is

approximately horizontal.

The fluid head can be levelled by loosening the ball level

clamp nut and bringing the bubble inside bullseye of bubble

level, tighten clamp nut.

To collapse the tripod, hold the tripod by the bowl, then

loosen the leg locks of the extended sections and lower the

bowl down until you hear an audible click of Q-lock latch.

The rubber foot can be serviced by using a 19mm spanner.

The leg pivot tension can be adjusted using a 17mm

spanner (supplied).

Maintenance

•

Keep clean, free from sand and dirt from leg locks & leg

angle adjusters.

•

If dirty, rinse with clean fresh water.

•

Don't use solvents, methylated spirits can be used on a

clean cotton wipe.

•

Use recommended lubricants only.

•

For more support ask your Miller service agent or contact

us at

millertripods.com/contact

Storage and transport

Whilst not in use, we recommend you keep your Miller Tripods

dry, clean & away from direct sunlight, stored in Miller Tripods

bag.

Optional Accessories

1520 Shoulder Strap

P5957 Transport Strap

P6005 17mm Spanner

1590 Solo-Q Leg Covers (Set of 3)

394 Solo-Q Dolly

3516 Solo-Q 2-stage Tripod Bag

3512 LW 1-stage Tripod Bag

Warranty

MILLER offers 3 years parts and labour warranty.

Please refer to MILLER Warranty Card D3993 for complete

details or our website.