Miller CS310A Panduan Pemilik - Halaman 6

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Senter Miller CS310A. Miller CS310A 20 halaman.

Halaman Cetak

READ INSTRUCTIONS.

D Read and follow all labels and the Owner's

Manual carefully before installing, operating, or

servicing unit. Read the safety information at

the beginning of the manual and in each section.

1-3. Proposition 65 Warnings

WARNING: This product can expose you to chemicals in-

cluding lead, which are known to the state of California to

cause cancer and birth defects or other reproductive

harm.

For more information, go to www.P65Warnings.ca.gov .

1-4. Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,

is available as a free download from the American Welding Society at

http://www.aws.org or purchased from Global Engineering Documents

(phone: 1-877-413-5184, website: www.global.ihs.com).

Safe Practice For Occupational And Educational Eye And Face Protec-

tion, ANSI Standard Z87.1, from American National Standards Institute,

25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, web-

site: www.ansi.org).

Safe Practices for the Preparation of Containers and Piping for Welding

and Cutting, American Welding Society Standard AWS F4.1, from Glob-

al Engineering Documents (phone: 1-877-413-5184, website: www.glo-

bal.ihs.com).

Safe Practices for Welding and Cutting Containers that have Held Com-

bustibles, American Welding Society Standard AWS A6.0, from Global

Engineering Documents (phone: 1-877-413-5184,

website: www.global.ihs.com).

National Electrical Code, NFPA Standard 70, from National Fire Protec-

tion Association, Quincy, MA 02169 (phone: 1-800-344-3555, website:

www.nfpa.org and www. sparky.org).

1-5. EMF Information

Electric current flowing through any conductor causes localized electric

and magnetic fields (EMF).The current from arc welding (and allied pro-

cesses including spot welding, gouging, plasma arc cutting, and induc-

tion heating operations) creates an EMF field around the welding circuit.

EMF fields can interfere with some medical implants, e.g. pacemakers.

Protective measures for persons wearing medical implants have to be

taken. For example, restrict access for passers−by or conduct individu-

al risk assessment for welders. All welders should use the following pro-

cedures in order to minimize exposure to EMF fields from the welding

circuit:

1. Keep cables close together by twisting or taping them, or using a

cable cover.

2. Do not place your body between welding cables. Arrange cables

to one side and away from the operator.

3. Do not coil or drape cables around your body.

OM-251981 Page 2

D Use only genuine replacement parts from the manufacturer.

D Perform installation, maintenance, and service according to the

Owner's Manuals, industry standards, and national, state, and loc-

al codes.

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,

from Compressed Gas Association, 14501 George Carter Way, Suite

103, Chantilly, VA 20151 (phone: 703-788-2700, website:

www.cganet.com).

Safety in Welding, Cutting, and Allied Processes, CSA Standard

W117.2, from Canadian Standards Association, Standards Sales, 5060

Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5NS

(phone: 800-463-6727, website: www.csagroup.org).

Safe Practice For Occupational And Educational Eye And Face Protec-

tion, ANSI Standard Z87.1, from American National Standards Institute,

25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, web-

site: www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, NFPA Standard 51B, from National Fire Protection Association,

Quincy, MA 02169 (phone: 1-800-344-3555, website: www.nfpa.org).

OSHA, Occupational Safety and Health Standards for General Indus-

try, Title 29, Code of Federal Regulations (CFR), Part 1910.177 Subpart

N, Part 1910 Subpart Q, and Part 1926, Subpart J, from U.S. Govern-

ment Printing Office, Superintendent of Documents, P.O. Box 371954,

Pittsburgh, PA 15250-7954 (phone: 1-866-512-1800) (there are 10 OS-

HA Regional Offices—phone for Region 5, Chicago, is 312-353-2220,

website: www.osha.gov).

4. Keep head and trunk as far away from the equipment in the

welding circuit as possible.

5. Connect work clamp to workpiece as close to the weld as

possible.

6. Do not work next to, sit or lean on the welding power source.

7. Do not weld whilst carrying the welding power source or wire

feeder.

About Implanted Medical Devices:

Implanted Medical Device wearers should consult their doctor and the

device manufacturer before performing or going near arc welding, spot

welding, gouging, plasma arc cutting, or induction heating operations.

If cleared by your doctor, then following the above procedures is recom-

mended.