Panasonic AGDVC20P - 3 CCD DV CAMCORDER Panduan Petunjuk Pengoperasian - Halaman 19
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Camcorder Panasonic AGDVC20P - 3 CCD DV CAMCORDER. Panasonic AGDVC20P - 3 CCD DV CAMCORDER 42 halaman. Agmini-dv camera/recorder
Juga untuk Panasonic AGDVC20P - 3 CCD DV CAMCORDER: Panduan Petunjuk Pengoperasian (40 halaman), Panduan Petunjuk Pengoperasian (42 halaman)
Halaman Cetak
ª
Recording mode
You can switch the tape recording mode.
≥Set to Tape Recording/Playback Mode.
1
Set [BASIC] or [ADVANCE] >> [REC SPEED] >> [SP] or
[LP].
If the LP mode is selected, the recording time will be 1.5 times
the SP mode, but some functions will be disabled.
≥We recommend using the SP mode for important recording.
≥In order to fully exhibit the performances of the LP mode, we
recommend using Panasonic cassettes marked LP mode.
≥It is not possible to dub audio onto image recorded in the LP
mode. (
)
-30-
≥In the LP mode, the picture quality will not be degraded in
comparison with the SP mode, but mosaic noise may appear
on the playback image or some functions may be disabled.
≥Playback on other digital video equipment or on digital
video equipment without the LP mode
≥Playback of the image on other digital video equipment
recorded in the LP mode
≥Slow/frame-by-frame playback
Recording on a tape
Remove the lens cap. (
)
-9-
(When the camera-recorder is turned on with the lens cap fitted,
the automatic white balance adjustment may not function
properly. Please turn the camera on after removing the lens
cap.)
≥Set to Tape Recording Mode.
CAMERA
VCR
1
Press the recording start/stop button (or sub recording
start/stop button) to start recording.
2
Press the recording start/stop button (or sub recording
start/stop button) again to pause recording.
≥For the recording time on a tape, refer to
≥Carry out a recording check (
recorded properly.
≥In order to find the unrecorded section, carry out the blank
search (
).
-19-
.
-11-
) to verify that the image is
-19-
Record mode
ª
On-screen display in the tape recording mode
1) Recording time elapse
2) Remaining tape indication
ª
Concerning the remaining tape time indication on
the screen
≥The remaining tape time is indicated in minutes. (When it
reaches less than 3 minutes, the indication starts flashing.)
≥During a 15-second or shorter recording, the remaining tape
time indication may not be displayed or the remaining tape
time may not be displayed correctly.
≥In some cases, the remaining tape time indication may
display remaining tape time that is 2 to 3 minutes shorter than
the actual remaining tape time.
Check the recording
The last image recorded is played back for 2 to 3 seconds.
After checking, the camera-recorder will be set to a recording
pause.
≥Set to Tape Recording Mode.
1
Press the [ENTER] button during the recording pause
until the icon 1 appears.
2
Press the [4] button to select the recording check icon
[
].
Blank search function
Searches for the last part of the image recorded (unused part of
the tape).
≥Set to Tape Recording/Playback Mode.
1
Set [BASIC] or [ADVANCE] >> [BLANK SEARCH] >>
[YES].
ª
Stopping blank search midway through
Press the [4] button to select the [∫] icon.
≥If the cassette tape has no blank part, then the camera-
recorder will stop at the end of the tape.
≥The camera-recorder stops at a point approx. 1 second
before the end of the last image recorded. When you start
recording at that point, the image can be recorded seamlessly
from the last image.
19