HP 316095-B21 - StorageWorks Edge Switch 2/24 Catatan Rilis - Halaman 30

Jelajahi secara online atau unduh pdf Catatan Rilis untuk Beralih HP 316095-B21 - StorageWorks Edge Switch 2/24. HP 316095-B21 - StorageWorks Edge Switch 2/24 32 halaman. Edge switch release notes
Juga untuk HP 316095-B21 - StorageWorks Edge Switch 2/24: Manual Pembaruan (9 halaman), Manual (41 halaman), Manual (40 halaman), Catatan Rilis (27 halaman), Manual (26 halaman), Catatan Rilis (27 halaman), Catatan Rilis (25 halaman), Panduan Petunjuk Instalasi (24 halaman), Catatan Rilis (23 halaman), Catatan Rilis (23 halaman), Catatan Rilis (22 halaman), Catatan Rilis (23 halaman), Catatan Rilis (19 halaman), Catatan Rilis (19 halaman), Catatan Rilis (18 halaman), Petunjuk Manual (17 halaman), Catatan Rilis (17 halaman), Petunjuk Peningkatan (16 halaman), Petunjuk Manual (16 halaman), Panduan Petunjuk Instalasi (16 halaman), Catatan Rilis (16 halaman), Catatan Rilis (17 halaman), Catatan Rilis (17 halaman), Catatan Rilis (11 halaman)

Workaround

The LAN connection must be restored. Stopping HAFM has no impact on the Fibre

Channel operations of any edge switch or director. Monitoring switch operations,

logging events, and implementing conﬁguration changes are interrupted only while

the LAN is not connected.

Effect of no LAN connection to HAFM appliance during boot up

If the HAFM appliance has no LAN connection while booting up, but it is connected

after booting up, the remote client sessions to the HAFM appliance are not allowed.

Also, the IP address that is displayed when you select SAN > Server Properties is

possibly incorrect.

Workaround

This is corrected by restoring the LAN connection and rebooting the appliance.

Rebooting the appliance has no impact on the Fibre Channel operations of any switch

or director. Only monitoring switch operations, logging events, and implementing

conﬁguration changes are interrupted.

Setting HAFM appliance LAN to use DHCP is activated to wrong LAN

When setting the IP conﬁguration for the HAFM appliance using the LCD panel,

setting DHCP conﬁguration for LAN 1 causes LAN 2, not LAN 1, to be conﬁgured for

DHCP. Similarly, setting DHCP conﬁguration for LAN 2 causes LAN 1, not LAN 2, to

be conﬁgured for DHCP.

Workaround

If you wish to conﬁgure LAN 1 for DHCP, select LAN 2 instead of LAN 1 at the start of

the conﬁguration procedure. If you wish to conﬁgure LAN 2 for DHCP, select LAN 1

instead of LAN 2 at the start of the conﬁguration procedure.

Event notiﬁcation by e-mail or call home can be missing information under

certain conditions

Though very unlikely, it is possible that an Event Notiﬁcation by e-mail or call home may

be missing information normally contained in these messages. This occurs if a switch

detects an event that requires a notiﬁcation to be issued, but HAFM has not completed

discovery of the switch. This discovery of a switch is usually completed within a few

seconds, so it is unlikely, though not impossible, that an event occurs during this short

span of time. Discovery of a switch occurs when it is added to HAFM for management,

and when the Ethernet connection to a switch is broken and reestablished, such as

when a switch's ﬁrmware is upgraded.