HP ProCurve 1600M Panduan Pengguna - Halaman 6

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Beralih HP ProCurve 1600M. HP ProCurve 1600M 8 halaman. Redundant power supply
Juga untuk HP ProCurve 1600M: Lembar Spesifikasi (12 halaman), Baca Saya Terlebih Dahulu (8 halaman), Panduan Peninjau (27 halaman), Panduan Tambahan (2 halaman), Panduan Tambahan (2 halaman), Panduan Instalasi (28 halaman), Panduan Instalasi (36 halaman), Panduan Instalasi (28 halaman), Panduan Pengaturan Cepat (2 halaman), Panduan Pengaturan Cepat (4 halaman), Suplemen Manual (28 halaman), Baca Saya Terlebih Dahulu (16 halaman), Instalasi dan Penghapusan (2 halaman), Panduan Instalasi (12 halaman), Panduan Perencanaan dan Pelaksanaan (40 halaman), Petunjuk Pembongkaran Akhir Masa Pakai Produk (2 halaman), Panduan Instalasi (46 halaman), Panduan Diagnostik (2 halaman), Petunjuk Pembongkaran (2 halaman)

Page 6-94; Reserved Addresses Excluded from IP Multicast (IGMP) Filtering. Traffic to IP

multicast groups in the IP address range of 224.0.0.0 to 224.0.0.255 will always be flooded because

addresses in this range are ''well-known'' or ''reserved'' addresses. Thus, if IP Multicast is enabled

and there is an IP multicast group within the reserved address range, traffic to that group will be

flooded instead of filtered by the switch.

Page 6-100; Automatic Broadcast Control (ABC). In order for ABC to operate, the switch must

be configured with a valid IP address.

Page 8-3; Telnet (or Web Browser Interface) Access Problem. If one or more IP authorized

managers are configured, the switch allows inbound Telnet (or web browser interface) access only

to a device having an authorized IP address. For more information on IP authorized managers, see

the Software Update C.7.XX Release Notes for the HP ProCurve Switch 1600M, 2424M, 4000M, and

8000M, shipped with the switch (beginning in the 2nd quarter of 1999) and also available in the

Support area of HP's ProCurve website at http://www.hp.com/go/procurve.

Page 8-11; Troubleshooting: Changed Event Type in Console Event Log and More

Information in Event Log Help Screen. In the table at the top of the page, replace the fault event

type with the FFI (Find, Fix, and Inform) event type. FFI event types are available in both the console

Event Log and the web browser interface Alert Log. Also, additional Help information for FFI events

has been added to the Event Log Help in the switch console.

Intrusion Log Notation. If you reboot the switch or display the Intrusion Log and reset the alert

flags, the log will list the time and date of all intrusions present at the time of the reboot or reset as

''prior to'' that time. For example, if the Intrusion Log includes an intrusion entry for port A2 at 4:51

p.m. on September 10, 1999, and you reboot the switch at 8:35 a.m. on September 14, 1999, the entry

for that intrusion would appear as prior to 14-Sept-99 8:35:00 AM. For more on port security and the

Intrusion Log, see the Software Update C.7.XX Release Notes for the HP ProCurve Switch 1600M,

2424M, 4000M, and 8000M, shipped with the switch and also available in the Support area of HP's

ProCurve website at http://www.hp.com/go/procurve.

Switch 8000M Power Supply Requirements

If you plan to install six or more HP ProCurve Switch 100Base-FX modules (HP J4112A) in the Switch

8000M, you must first install a second Switch 4000M/8000M (Redundant) Power Supply (HP J4119A)

in the switch. Note that if a redundant power supply is installed and one of the switch's power supplies

subsequently fails, you can replace the failed power supply without disrupting switch operation.