Panasonic WV-CP470 Series Panduan Petunjuk Pengoperasian - Halaman 3
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Kamera Digital Panasonic WV-CP470 Series. Panasonic WV-CP470 Series 13 halaman. Colour cctv cameras
Juga untuk Panasonic WV-CP470 Series: Panduan Petunjuk Pengoperasian (13 halaman), Spesifikasi (2 halaman)
Halaman Cetak
!5 Alarm Output Terminal (ALARM OUT/GND)
Connects to the alarm input connector (terminal) of an external device. When the cam-
era detects motion, the alarm output signal is supplied to the connected external device
(Open collector output: 16 V DC, 100 mA max).
!6 Day/Night Input Terminal (DAY/NIGHT IN/GND)
This terminal is used for connecting the camera to an external day/night detecting sen-
sor.
!7 AC Inlet Socket
Plug the power cord (supplied as a standard accessory) into this socket and connect it
to an AC outlet.
!8 AC/DC Compatible Input Terminal
(DC 12 V IN/AC 24 V IN)
This terminal is for connecting the 12 V DC or 24 V AC power supply cord.
Note: Do not exceed the ratings of the voltage or current when connecting the external
device.
Caution:
Connect to 12 V DC (10.8 V to 16 V) or 24 V AC (19.5 V to 28 V) class 2 power supply
only. Be sure to connect the grounding lead to the GND terminal when the power is
supplied from a 24 V AC power source.
CONNECTIONS
A. WV-CP470 (220 V to 240 V AC 50 Hz)
Plug the AC power cord (supplied as standard accessory) into the AC inlet socket and con-
nect it to a 220 V to 240 V AC 50 Hz outlet.
Notes:
• Connect the power cord firmly.
• The power cord should be long enough for panning and tilting.
If the cable is too short, the power cord plug may be pulled off the camera when the
camera pans or tilts.
B. WV-CP474E (12 V DC/24 V AC)
The WV-CP474E has an AC/DC compatible input terminal. The 12 V DC or 24 V AC power
supply cord can be connected to this terminal. The camera detects the power source auto-
matically.
1. 12 V DC Power Supply
Connect the power cord to the AC/DC compatible input terminal on the rear panel of the
camera.
12 V DC
(10.8 V - 16 V)
• Calculation of maximum cable length between camera and power supply
10.8 V DC ≤ V
L : Cable length (m)
R : Resistance of copper wire (Ω/m)
V
: DC output voltage of power supply
A
unit
2. 24 V AC Power Supply
Connect the power cable to the AC/DC compatible input terminal on the rear panel of
the camera.
24 V AC, 50 Hz
(19.5 V - 28 V)
Video Cable
1. It is recommended to use a monitor
whose resolution is at least equal to
that of the camera.
2. The maximum extensible coaxial
cable length between the camera
and the monitor is shown in the
table.
Alarm Connections
1. Connect an external sensor to the DAY/NIGHT terminal.
2. Connect an external device such as a buzzer or lamp to the ALARM terminal.
• The alarm output terminal is an open collector terminal with a capacity of 16 V DC, 100
mA or less.
OFF: Open contact
ON: 100 mA or less
• Colour/black-and-white input terminal with a capacity of 5 V DC pull-up input, 0.2 mA or
more.
OFF: Open contact
ON: Closed contact
Notes:
• Use a relay unit if the voltage or current of the connected device exceeds the ratings.
• To validate the Day/Night function, set BW mode to EXT on the special menu.
GND
1
1
2
2
AC 24V IN
DC 12V IN
- (R x 0.42 x L) ≤ 16 V DC
A
GND
GND
1
1
2
2
AC 24V IN
DC 12V IN
Resistance of copper wire [at 20 °C (68 °F)]
Copper wire
#24
size (AWG)
(0.22mm
Resistance
0.078
Ω/m
Resistance
0.026
Ω/ft
L standard =
L minimum =
L maximum =
Recommended wire gauge sizes for 24 V AC line.
Copper wire
#24
size (AWG)
(0.22mm
Length
(m)
95
of Cable
(Approx.) (ft)
314
Type of
coaxial cable
Recommended (m)
maximum
cable length
(ft)
#22
#20
) (0.33mm
) (0.52mm
2
2
0.050
0.030
0.017
0.010
− 12
V
A
(m)
0.42 x R
− 16
V
A
(m)
0.42 x R
− 10.8
V
A
(m)
0.42 x R
#22
#20
2
) (0.33mm
2
) (0.52mm
150
255
495
842
RG-59/U RG-6/U RG-11/U RG-15/U
(3C-2V) (5C-2/V) (7C-2V)
250
500
600
825
1 650
1 980
#18
) (0.83mm
)
2
2
0.018
0.006
#18
2
) (0.83mm
2
)
425
1 403
(10C-2V)
800
2 640