Diamond Products CC800M Panduan Operator - Halaman 5
Jelajahi secara online atau unduh pdf Panduan Operator untuk Melihat Diamond Products CC800M. Diamond Products CC800M 8 halaman. Core cut masonry saw
Halaman Cetak
CAUTION:
If
cart is not held back at end of cut. blade may draw material in so
damage
will
occur.
4.
When
finished
sawing,
engine
manual.)
WARNING:
Never
MAINTENANCE:
1.
Clean water
tub once a day
accumulates, it can damage
2.
Clean saw each night after use.
3.
Lubricate blade
Grease provides an added protective seal for bearings. Use only premium Lithium 12 based grease
conforming
to NLGI grade
bearings immediately. Grease blade shaft bearings while saw is running.
and before saw is
4.
Between jobs or extended periods of storage, clean saw with a
thoroughly lubricate all moving parts. Check to make sure all fasteners are tight.
5.
Ensure that extension cord gauge matches its length.
damage
motor.
6.
If
you
experience any problems
nearest Authorized Service Center. If motor or engine is serviced by an unauthorized service
warranty will
7.
When transporting saw, remove cutting head from frame.
cutting head to pound
when
transporting.
8.
Make
sure that V-belts are always tensioned properly. Replace worn belts in sets.
9.
Slots
in cutting head are provided to keep blade aligned horizontally and vertically
conveyor
cart. Loosen lock nuts on blade shaft bearings and
Tighten
lock
10.
Blade should mount snugly
inner
flange
must
11.
Blade
flanges
can shorten blade life or cause blade to break.
12.
Frequently inspect conveyor cart. Replace
13.
Replace bronze bearing in blade
14.
Clean air cleaner daily
15.
For
additional
Diamond Products manufactures diamond blades
block .tile, refractory etc.
at
1-800-321-5336 or 1 -800-421-3157
the motor
or
engine off.
turn
leave the saw unattended when running.
- twice
a day during heavy cutting - and refill
water
pump and shorten blade life.
Flush
pump and hoses with clean
shaft
and pivot
shaft
bearings daily.
#2
consistency,
stored.
Use 230 volts. Inspect cord for cuts, nicks,
with your
be voided.
in
the frame,
causing
nuts when blade is properly aligned
on
arbor. If blade fits loosely on arbor,
be
replaced.
Otherwise, blade life
must have minimum outside diameter
guard
pivot plate if blade guard does not pivot properly.
on saws with
gas engine.
engine care,
see
engine manual.
ABOUT DIAMOND BLADES
Contact
a Diamond Products Customer
to help determine
(Note: Allow gas engine
water.
When
cutting dry, grease bearings
without
Molybdenum Disulfide.
wire
brush to remove
as
shown
in
chart.
or
exposed
electric motor or
gas
engine.
Vibration
the head to come out of alignment.
tilt
shaft towards appropriate
with
conveyor cart.
or
will
be shortened
of
3 7/8".
Replace worn
wood insert
and
wheels often.
See
engine manual for maintenance instructions.
suited
for your
specific
Service
what
blade is right
fast that blade
to cool
down.
with
clean
water. If sludge
once or
twice daily.
Replace
damaged or noisy
Grease
bearings at end of job
dried
sludge. Clean and
Undersize extension cords may
wires.
Replace cord if damaged.
contact
Diamond Products for the
center,
during transport could
cause
Always
remove
with
cut l i ne on
direction.
if arbor shoulder
is
grooved,
dramatically.
flanges
immediately
cutting
needs –
brick,
Representative
for your specific
See
the
the
the
blade
the
because they
concrete
needs.
5