Panasonic PT-AE1000 Panduan Petunjuk Pengoperasian - Halaman 20
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Proyektor Panasonic PT-AE1000. Panasonic PT-AE1000 28 halaman. Panasonic lcd projector operating instructions
Juga untuk Panasonic PT-AE1000: Panduan Petunjuk Pengoperasian (28 halaman)
Halaman Cetak
OPTION Menu
tttr
m
<x>
• See 'Navigating through
the MENU" on page 28.
INPUT GUIDE
SIMPLE
DETAILED
OSD DESIGN
^ou can change the background colour of the menu.
Press -4 ► to cycle through the options.
- -0p"°"s 1
Func,l°"
TYPE1
Semi transparent black
_TYPE2
iolkTbiue
_TYPE3
Semi transparent dark blue
WSK:
JJJIP
W/Kk
Wmm;
OSD POSITION
You can change the position where to display the menu.
;s INPUT or the INPUT SELECT button
iput method, the guidance is indicated in
corner of the screen. The following
s are available. Press ◄ ► to cycle
ions.
Turn off the guidance.
Display the inpuFmethoaTby text.
The INPUT GUIDE will go out after
5 seconds without any operation.
Display theuTpuFmettFod by
graphic.
The INPUT GUIDE will go out after
10 seconds without any operation.
UPPER
LEFT
UPPER
CENTRE
UPPER
RIGHT
CENTRE
LOWER
LEFT
LOWER
CENTRE
LOWER
RIGHT
BACK COLOUR
You can choose a BLUE or BLACK screen for when the
projector is idle. Press M ► to select an option.
STARTUP LOGO
You can switch the logo on/off that is displayed when
starting up. Press ◄ ► to select an option.
• ON:
Active
* OFF:
Deactive
AUTO SEARCH
When the projector is turned on, the input terminals are
detected and an input signal is selected automatically
You can switch the system on/off. Press ◄ ► to select
an option.
* ON:
Active
* OFF:
Deactive
NOTE:
• When no signal is detected, the last used input
method will be selected.
HDMI SIGNAL LEVEL
When an HDMI is selected, you can switch the HDMI
signal level NORMAL or EXPAND to display the image.
Press ◄ ► to select an option.
NOTE:
~~~
~
• HDMI SIGNAL LEVEL is not available with some
equ
INSTALLATION
When installing the projector, select the projection
method according to the projector position. Press ◄ ►
to cycle through the options. See "Projection method"
on page 15.
iTI DESK
REAR/DESK
REAFUCEILING
SLEEP
Setting on a desk/floor and
projecting from front
Mounting in the ceiling and
projecting from front
Setting on a desk/floor and
projecting from rear
Mounting in the ceiling and
projecting from rear
You can select the required duration of time and set the
off timer to turn off the POWER of the projector
automatically. 3 minutes before turn-off, the countdown
of minutes will be displayed in the lower right corner.
Press ◄ ► to cycle through the options. See "Switching
off the projector automatically" on page 25.
ALTITUDE
If you use the projector at high elevations, set the fan
speed to HIGH. Press ◄ ► to select HIGH or LOW
NOTE:
• At 1 400 m (4593 ft) above sea level, the setting
must be HIGH.
LAMP POWER
You can adjust the power of the lamp to save on
electricity, prolong the lamp life and reduce the noise.
Options
NORMAL
ECO-MODE
When higher luminance is
required such as movies
When lower luminance is
sufficient such as in a small room
NOTE:
• When no input signal is detected, the function is
disabled.
OPTIOmVjerui
lampruStH
You can check how long the lamp has been used.
NOTE:
• LAMP RUNTIME is a relevant matter for lamp
replacement timing. See "Care and Replacement'
on page 41.
FUNCTION BUTTON
You can assign the frequently use functions to each
function buttons and access to the functions instantly
| FUNCTION SUTTON
|
FUNCTION BUTTON2
11_ FUNCTION BUTTON3
1.
Press A T to select the required button to assign
2.
Press ENTER,
3.
Press ◄ ► to select the required function to
assign.
4.
Press RETURN or MENU to return to the previous
menu, or press repeatedly to return to the
projection.
DISABLED
SHUTTER
HDMI2 IN
HDMI1 IN
PC IN
SCART IN
AUTO SETUP
VIDEO IN
S-VIDEO IN
COMPONENT IN
B
SHUTTER function
You can turn off the lamp and stop the projection
temporary for electrical power save. Press any
button except the LIGHT, PROJECTOR or
Learning Remote control buttons to return to the
projection.
NOTE:
• See "Selecting the input signal" on page 21,
"AUTO SETUP" on page 36.
» The function buttons are also used as Learning
Remote control buttons. Press the DEVICE button
to switch the control mode. See "Remote Control
Plnorato rtiiiHo" nrrmiHor) with th<=> nrniortnr