Panasonic PT-DZ110XE ( ) Spesifikasi - Halaman 6
Jelajahi secara online atau unduh pdf Spesifikasi untuk Proyektor Panasonic PT-DZ110XE ( ). Panasonic PT-DZ110XE ( ) 6 halaman. 3-chip dlp projector
Juga untuk Panasonic PT-DZ110XE ( ): File Spesifikasi (19 halaman)
Halaman Cetak
Specifications
Model
Power supply
Power consumption
DLP
chip
Panel size
™
Display method
Pixels
Lens
Lamp
Screen size (diagonal)
1
Brightness*
1
Centre-to-corner uniformity*
Contrast*
1
Resolution
Scanning frequency
SDI
HDMI/DVI-D/RGB
YP
P
(YC
C
)
B
R
B
R
Video/S-Video
Optical axis shift
Vertical
Horizontal
Keystone correction range
Installation
Terminals
SDI IN
HDMI IN
DVI-D IN
RGB 1 IN
RGB 2 IN
VIDEO IN
S-VIDEO IN
SERIAL IN
SERIAL OUT
REMOTE 1 IN
REMOTE 1 OUT
REMOTE 2 IN
LAN
Cabinet materials
Dimensions (W × H × D)
Weight
Operating environment
Supplied accessories
* 1 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards. * 2 With the
over the L AN network will not operate, and the serial output terminal cannot be used. Also, only certain commands can be received for external control using the serial terminal. * 3 1.78 –7.62 m ( 70 –300 inches ) with the
E T-D75LE50. * 4 When using only the K E YSTONE correction. When using both the K E YSTONE and ARC corrections of the Geometric Adjustment function: vertical ± 5°, horizontal ± 5° (vertical ±10° and horizontal ±15° with the
E T-D75LE40 / D75LE8 ). * 5 WUXG A resolution is supported only when the signals are compliant with VESA CV T-RB ( Coordinated Video Timing-Reduced Blanking ). * 6 The operating temperature range is 0°C ( 32°F ) to 40°C (104°F )
when used in High-Altitude mode (1,400 m (4,593 ft) to 2,700 m ( 8,858 ft) ).
N O T E S O N U S E
1. Do not install the projector in locations that are subject to excessive water, humidity, steam, or oily smoke. Doing so may
result in fire, malfunction, or electric shock.
2. The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large
sound, or fail to illuminate, due to impact or extended use.
3. The projector uses of high-wattage lamp that becomes very hot during operation. Please observe the following precautions.
• Never place objects on top of the projector while it is operation.
• Make sure there is an unobstructed space of 500 mm (1 ft 8 in) or more around the projector's exhaust openings.
• Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection.
When stacking projector units, be sure to provide the amount of space indicated between them. These space require-
ments also apply to installation where only one projector unit is operating at one time and the other unit is used as a
backup.
• If the projector is placed in a box or enclosure, temperature of the air surrounding the projector must be between 0°C
Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product may be subject to export
regulations. All other trademarks are the property of their respective trademark owners. Projection Images simulated. DLP, DLP logo and DLP
Medallion logo are trademarks or registered trademarks of Texas Instruments. The PJLink trademark is an application trademark in Japan, the
United States, and other countries and regions or registered trademarks. © 2012 Panasonic Corporation All rights reserved.
PT- D Z1 10 X E
220–240 V AC, 5.0 A, 50/60 Hz
920 W (980 VA at 240 V)
(0.3 W with
set to
. *
2
STANDBY MODE
ECO
8 W with
set to
.
STANDBY MODE
NORMAL
Both with fan stopped.)
24.4 mm (0.96 in) diagonal (16:10 aspect ratio)
DLP
chip × 3 (R, G, B), DLP
projection system
™
™
2,304,000 (1,920 × 1,200) × 3,
total of 6,912,000 pixels
Optional powered zoom/focus lenses
355 W UHM lamp × 2 (dual lamp system)
1.78 –15.24 m (70–600 in)*
3
(16:10 aspect ratio)
10,600 lm (dual lamp, high mode)
90 %
10,000:1 (full on/full off, in dynamic iris 3 mode)
1,920 × 1,200 pixels
SD-SDI signal: 480i, 576i (SMPTE 259M compliant)
Single-link HD-SDI signal: 720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p,
1080/24p, 1080/24sF, 1080/30p (SMPTE 292M compliant)
f
15 kHz–100 kHz, f
24 Hz–120 Hz, dot clock 162 MHz or lower
H
V
f
15.75 kHz, f
60 Hz [525i (480i)]
f
H
V
H
f
15.63 kHz, f
50 Hz [625i (576i)]
f
H
V
H
f
31.50 kHz, f
60 Hz [525p (480p)]
f
H
V
H
f
31.25 kHz, f
50 Hz [625p (576p)]
f
H
V
H
f
15.75/15.63 kHz, f
50/60 Hz [NTSC, NTSC4.43, PAL, PAL60, PAL-N, PAL-M, SECAM]
H
V
±55% from centre of screen (powered)
(±44% with the ET-D75LE6)
±20% from centre of screen (powered)
(±15% with the ET-D75LE6)
Vertical: ±40° (±22° with the ET-D75LE50, ±28° with the ET-D75LE6)*
Ceiling/floor, front/rear
BNC × 1
SD-SDI signal (YC
C
4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i
B
R
Single-link HD-SDI signal (YP
P
4:2:2 10-bit): SMPTE 292M compliant: 720/50p,
B
R
720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
HDMI 19-pin × 1 (Deep Colour, compatible with HDCP, 480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p,
1080/30p, 1080/60p, 1080/50p (non-interlaced signals only), VGA (640 × 480) – WUXGA*
DVI-D 24-pin × 1 (DVI 1.0 compliant, compatible with HDCP, compatible with single link only,
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
VGA (640 × 480) –WUXGA*
5
(1,920 × 1,200), compatible with non-interlaced signals only, dot clock: 25 –162 MHz
BNC × 5 (RGB/YP
P
/YC
C
× 1)
B
R
B
R
D-Sub HD 15-pin (female) × 1 (RGB/YP
BNC × 1 (composite video)
Mini DIN 4-pin × 1 (S-Video)
D-sub 9-pin (female) × 1 (for external control, RS-232C compliant)
D-sub 9-pin (male) × 1 (for link control, RS-232C compliant)
M3 jack × 1 (for wired remote control)
M3 jack × 1 (for link control)
D-sub 9-pin (female) × 1 (for external control, contact control)
RJ-45 × 1 (for network connection, 10Base-T/100Base-TX, compliant with PJLink™)
Moulded plastic
530 × 200 × 548.5 mm (20-7/8 × 7-7/8 × 21-19/32 in) (with legs at shortest position, optional lens not included)
Approximately 24 kg (52.9 lb) (optional lens not included)
Operating temperature: 0°C–45°C (32°F–113°F)*
Power cord with security lock, wireless/wired remote control unit, batteries for remote control (R6/LR6 type × 2), safety wire rope
PT- D S 10 0 X E
220–240 V AC, 4.8 A, 50/60 Hz
900 W (950 VA at 240 V)
(0.3 W with
set to
STANDBY MODE
Both with fan stopped.)
24.1 mm (0.95 in) diagonal (4:3 aspect ratio)
DLP
chip × 3 (R, G, B), DLP
™
1,470,000 (1,400 × 1,050) × 3,
total of 4,410,000 pixels
1.78 –15.24 m (70–600 in)*
1,400 × 1,050 pixels
(Input signals that exceed this resolution will
be converted to 1,400 × 1,050 pixels.)
45.00 kHz, f
60 Hz [750 (720)/60p]
V
37.50 kHz, f
50 Hz [750 (720)/50p]
V
33.75 kHz, f
60 Hz [1035/60i]
V
33.75 kHz, f
60 Hz [1125 (1080)/60i]
V
±50% from centre of screen (powered)
(±40% with the ET-D75LE6)
±30% from centre of screen (powered)
(±20% with the ET-D75LE6)
5
, horizontal: ±15° (±10° with the ET-D75LE6)*
P
/YC
C
× 1)
B
R
B
R
6
, operating humidity: 10%–80% (no condensation)
set to
S T A N D B Y M O D E
(32°F) and 35°C (95°F). Also make sure the projector's intake and exhaust openings are not blocked. Take particular
care to ensure that hot air from the exhaust openings is not sucked into the intake.
4. If the projector is to be operated continuously 24 hours a day, use the multi-lamp optical system's alternating lamp opera-
tion (lamp changer) function. The projector can be operated continuously 24 hours a day in four-lamp operation mode, but it
will automatically operate with three lamps for 8 hours of the 24 hours.
5. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.
• The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp
characteristics and usage conditions.
• The brightness of the lamp will gradually decrease with use.
6. Because the ET-D75LE50 is a fixed short-throw lens, the lens shift function cannot be used with it.
7. Due to natural characteristics of lamps, screen brightness may vary (flicker). This is not an indication of faulty lamp per-
formance.
P T- D W9 0 X E
. *
2
8 W with
set to
ECO
STANDBY MODE
NORMAL
21.6 mm (0.85 in) diagonal (16:9 aspect ratio)
projection system
DLP
chip × 3 (R, G, B), DLP
™
™
1,049,088 (1,366 × 768) × 3,
total of 3,147,264 pixels
3
(4:3 aspect ratio)
1.78–15.24 m (70–600 in)*
9,600 lm (dual lamp, high mode)
1,366 × 768 pixels
(Input signals that exceed this resolution will
be converted to 1,366 × 768 pixels.)
–
f
28.13 kHz, f
50 Hz [1125 (1080)/50i]
H
V
f
28.13 kHz, f
25 Hz [1080/25p]
H
V
f
27.00 kHz, f
24 Hz [1080/24p]
H
V
f
27.00 kHz, f
48 Hz [1080/24sF]
H
V
±70% from centre of screen (powered)
(±60% with the ET-D75LE6)
±30% from centre of screen (powered)
(±20% with the ET-D75LE6)
–
5
(1,920 × 1,200), dot clock: 25 –162 MHz
. When the
is set to
E C O
S T A N D B Y M O D E
E C O
For more information about Panasonic projectors
http://panasonic.net/avc/projector
JQA-QMA14392
Factories of Business Solutions Business Group have received ISO
14001:2004—the Environmental Management System certification
(except for third parties' peripherals).
All information included here is valid as of June 2012.
.
projection system
™
3
(16:9 aspect ratio)
f
33.75 kHz, f
30 Hz [1080/30p]
H
V
f
67.50 kHz, f
60 Hz [1080/60p]
H
V
f
56.25 kHz, f
50 Hz [1080/50p]
H
V
4
, network functions such as power on
EC98J2010
051
PT-DZ110XE2 Printed in Japan.