Bionaire BASF1415 - 2 Buku Petunjuk - Halaman 2

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Kipas angin Bionaire BASF1415 - 2. Bionaire BASF1415 - 2 2 halaman.

Halaman Cetak

BASF1415 Fig. 1

BASF1415-IUK_09EM1.indd 4-6

U.K. AND IRELAND

PLEASE READ AND SAVE THESE

INSTRUCTIONS

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic safety

precautions should always be taken including

the following:

G H

• Use the fan only for purposes described in

the instruction manual.

• To protect against electrical shock, do not

immerse the fan, plug or cord in water or

spray with liquids.

• Close supervision is necessary when any

appliance is used by or near children.

• Unplug from the electrical outlet when not in

use, when moving the fan from one location

to another, before putting on or taking off

parts and before cleaning.

• Avoid contact with any moving parts.

• Do not operate in the presence of explosive

and/or flammable fumes.

• Do not place the fan or any parts near an open

flame, cooking or other heating appliance.

• Do not operate any appliance with a damaged

cord, plug, after the appliance malfunctions,

or has been dropped/damaged in any manner.

• The use of attachments not recommended or

sold by the appliance manufacturer may

cause hazards.

• Do not use outdoors.

• Do not let the cord hang over the edge of a table

or counter, or come into contact with hot surfaces.

• To disconnect from the electrical supply, grip

the plug and pull from the wall outlet.

DO NOT pull on the cord.

• Always use on a dry, level surface.

• Do not operate without the fan grills properly

in place.

• This product is intended for household use

ONLY and not for commercial or industrial

applications.

• If the supply cord or plug is damaged, it must

be replaced by the manufacturer or its service

agent or a similarly qualified person in order

to avoid hazard.

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the appliance by

a person responsible for their safety. Children

should be supervised to ensure that they do

not play with the appliance.

MISSING A PART FOR YOUR FAN?

Please call 0800 052 3615 for assistance.

ASSEMBLY INSTRUCTIONS (See Fig 1.)

Base/Pole assembly

You will need the base cover (N), weight (O),

pole (K,M), washer (R) and L-shaped locking

lever (P).

OPERATING INSTRUCTIONS

1. Turn the base cover upside down and place

the weight into the base cover.

1. Set the fan base on a dry level surface

2. Insert the threaded end of the L-shaped

2. Make sure the Selector (Speed) Control (S) is

locking lever into the hole of the washer,

in the OFF(0) position. Selector (Speed)

weight and through the base cover.

Control (S) is located on the top of the fan

motor housing.

3. Whilst holding the base cover and weight with

one hand, connect the pole to the base, sliding

3. Plug the cord into a suitable 220-240V. AC

the L-shaped locking lever into the bottom of

outlet.

the pole (M) with your other hand.

4. The SPEED is adjusted by turning the Selector

4. Turn the L-shaped locking lever clockwise to

(Speed) Control (S) to the desired setting:-

securely attach the pole to the base.

0-III-II-I.

5. Set the base on the floor, weight side down.

5. The OSCILLATION control (T) is located on

the top of the fan motor housing. To start

Fan head assembly

oscillation, push the control knob down. To

You are now ready to assemble the fan head

stop oscillation, pull the control knob up.

1. Unscrew rear grill mounting nut (D) before

ADJUSTMENT

positioning the rear grill (F) over the motor

shaft (G) making certain that the notches at

Tilt adjustment

the top and bottom of the rear grill, fit over the

Follow these instructions to tilt the fan head for

prongs on the motor housing (H).

upward angle air movement.

2. Secure the rear grill in its place using the rear

1. To change the tilting angle of the fan head,

grill mounting nut (D). Turn this nut clockwise

simply loosen the tilt adjustment knob (J)

and tighten firmly.

2. Move the fan head to the desired angle, then

3. Slide the fan blade (B) with the hollowed

firmly tighten the knob to lock in place.

interior of the blade facing toward the rear

Height adjustment

grill, firmly onto the motor shaft. The top of the

Follow these instructions to adjust the height of

motor shaft should lie even with the centre of

the fan.

the fan blade.

1. Turn the pole locking knob (L) anti-clockwise

4. Now use the securing screw (C) (already

attached to the Fan Blade) to lock the blade

to loosen the pole.

into place. Tighten the screw into the side hole

2. Adjust the pole to the desired height and

of the fan blade, against the motor shaft, until

firmly tighten the locking knob in a clockwise

both the blade and screw are secure.

direction.

5. Centre the front grill (A) by aligning the Bionaire

CLEANING AND MAINTENANCE

logo on the logo plate so that it is horizontal

Follow these instructions to correctly and safely

and parallel with the floor. Then, holding the

care for your Bionaire

front grill against the rear grill, push the black

• Always unplug the fan before cleaning or

grill ring (E) into place at the top and bottom of

assembly.

the fan. (Push directly on the black grill ring,

not on the grills themselves). Finish securing

• Do not allow water to drip on or into the fan

the grill ring in the same manner until both

motor housing.

grills are joined underneath the black ring.

• Be sure to use a soft cloth, moistened with a

mild soap solution.

Final assembly

• Do not use any of the following as a cleaner:

1. Slide the inner pole extension (K) up from the

petrol, thinners or benzene.

outer pole (M). Insert the pole locking knob (L)

into the hole on the outer pole, to securely

Fan Blade cleaning

hold this position.

(See instructions for fan head assembly)

2. Place the fan head assembly into this extension

1. To access the fan blade, remove the front grill

pole, inserting the neck of the fan into the pole

and securing screw.

opening. Turn the fan head's neck until the

2. Clean the fan blade, front and rear grills with

head is securely locked into place.

a soft moist cloth.

3. Add the tilt adjustment knob (J) to the hole in

3. Replace the fan blade, tighten screw and

the fan head's neck (I). Tighten when the fan

securely fasten the front grill.

head is in your desired position.

Fan head, base and pole cleaning

Converting to a table fan -

Using a soft, moist cloth, with or without a mild

On model BASF1415 an additional short pole

soap solution, carefully clean the fan base, pole

(Q) is supplied which allows the fan to be

and head. Please use caution around the motor

converted into a table fan. To change to this

housing area. Do not allow the motor or other

short pole, remove the fan head assembly from

electrical components to be exposed to water.

its position on top of the inner pole and unscrew

the L-shaped locking lever at the base. Remove

the long pole, replace with the short pole and

reassemble as detailed above.

FAN STORAGE

Your fan can be stored either partially disassembled

or assembled.

It is important to keep it in a safe, dry location.

• If stored disassembled, we recommend using

the original (or appropriately sized) box.

• If stored assembled or partially assembled,

remember to protect the fan head from dust.

FOR U.K. AND IRELAND ONLY:

If the plug is not suitable for the socket outlets in

your home, it can be removed and replaced by

a plug of the correct type. Please refer to

"Installation of a plug" below.

Installation of a plug Applicable to

U.K. and Ireland

NOTE: If the terminals in the plug are not

marked or if you are unsure or in doubt about

the installation of the plug please contact a

qualified electrician.

If a 13A 3-pin plug is fitted, it must be an ASTA

fan. Please remember:-

approved plug, conforming to BS1363 standard.

Replacement 3A fuses must be BSI or

ASTABS1362 approved.

This product is fitted with a 13A plug complying

to BS1363. If this plug is unsuitable or needs to

be replaced, please note the following:

The wires in the mains lead are coloured as

such:

BROWN -

LIVE

BLUE

NEUTRAL

Please note that the colour of these mains wires

may not correspond with the colour markings

that identify the terminals in your plug. Please

proceed as follows:

The BROWN coloured wire must be connected

to the terminal, which is marked with the letter

"L" or is coloured RED.

The BLUE coloured wire must be connected to

the terminal, which is marked with the letter "N"

or is coloured BLACK.

DO NOT CONNECT either of these wires to the

earth terminal in the plug. The earth terminal

plug is marked with the letter "E", or with the

earth symbol

, or coloured GREEN, or

GREEN and YELLOW.

6/9/09 9:58:25 AM