Alpha Professional Tools AIR-300 Buku Petunjuk - Halaman 3
Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Sander Alpha Professional Tools AIR-300. Alpha Professional Tools AIR-300 20 halaman. Pneumatic polisher
Juga untuk Alpha Professional Tools AIR-300: Catatan Teknis (4 halaman)
Halaman CetakSPECIFICATIONS
87PSI
10 CFM
6 Bar
280l/min
INTRODUCTION
Thank you for purchasing an Alpha
Polisher. This polisher is the workhorse of a complete
polishing system. A wide range of accessories help
you perform many different tasks. This tool lets you
grind, shape, bevel, contour and polish all kinds of
natural stone and man-made materials. You can eas-
ily change from one type of disc to another in just a
matter of seconds. The tool is used with water to help
you get the best possible finish, to reduce the health
risks of dust, and to give the most savings in time
and money. For your safety, please read this manual
thoroughly before you start operating this polisher.
ABOUT THE SYMBOLS
According to the hazard level, all safety notes in this
manual are classified into "DANGER", "WARNING"
and "CAUTION".
DANGER! - Death or serious personal injury is im-
minent when handling this polisher incorrectly.
WARNING! - There is a possibility of death or serious
personal injury when handling this polisher incorrectly.
CAUTION! - There is a possibility of personal
injury or property damage when handling this polisher
incorrectly.
NOTE: In some situations, failure to observe
WARNING notes could result in death or serious
personal injury. Be sure to read and observe the
safety notes to ensure safety and correct use of
the polisher.
SAFETY INSTRUCTIONS FOR POWER
TOOLS
1. Know Your Power Tool. Read owner's
manual carefully. Learn its applications and limita-
tions as well as specific potential hazards particular
to this tool.
2. Keep Work Area Clean. Cluttered areas and
benches invite accidents.
3. Avoid Dangerous Environments. Keep
work areas as dry as possible. Do not use tool in
presence of flammable liquids or gases. Keep the
area well lit.
1.60lbs
5,800RPM
.731kg
Pneumatic
®
1/4" BSPP 1/4" BSPT
4. Keep Children and Visitors Away. All visi-
tors should be kept a safe distance from the work
area. Keep out of reach of children.
5. Don't Force Tool. It will do the job better and
safer at the rate for which it was designed.
6. Wear Proper Apparel. Do not wear loose cloth-
ing or jewelry as it can get caught in moving parts.
Rubber gloves and insulated non-skid footwear
are recommended. Wear protective covering to
contain long hair.
7. Wear Proper Eye Protection. All users and
bystanders must always wear proper personal eye
protection which conform with ANSI/ISEA Z87.1
(CAN/CSA Z94.3). Also, use a face or dust mask
if operation is dusty. Always wear certified safety
equipment.
8. Wear Proper Ear Protection. All users
and bystanders must wear proper personal ear
protection which conforms with ANSI S12.6 (S3.19)
hearing protection.
9. Wear Proper Respiratory Protec-
tion. All users and bystanders must wear
proper personal respiratory protection. Al-
ways use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure.
WARNING! Some dust created by power
sanding, sawing, grinding, drilling, polishing and
other construction activities contains chemicals
known to the State of California to cause can-
cer, birth defects, or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks, cement and other
masonry products, and
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depend-
ing on how often you do this type of work.
To reduce your exposure, work in a well ven-
tilated area, and work with approved safety
5/8"-11
English
3