Epever BTBLANKET180 Manual - Halaman 4

Jelajahi secara online atau unduh pdf Manual untuk Panel surya Epever BTBLANKET180. Epever BTBLANKET180 4 halaman.

Halaman Cetak

Battery

Battery level shows current value, battery frame

Overheating

blink, fault icon blink

Load failure

Load overload

①

When load current reaches1.02-1.05 times 1.05-1.25 times, 1.25-1.35 times and

1.35-1.5 times more than nominal value, controller will automatically turn off loads in 50s,

30s,10s and 2s respectively

4.3 Load mode setting

Operating Steps:

Under load mode setting interface, press SET button and hold on 5s till the number begin

flashing, then press MENU button to set the parameter, press SET button to confirm.

Timer 1

Light ON/OFF

Load will be on for 1 hour

since sunset

Load will be on for 2 hours

since sunset

Load will be on for 3～13

～

hours since sunset

Load will be on for 14 hours

since sunset

Load will be on for 15 hours

since sunset

Test mode

Manual mode(Default load

ON)

NOTE: Please set Light ON/OFF, Test mode and Manual mode via Timer1. Timer2

will be disabled and display "2 n".

4.4 Battery Type

 Operating Steps

Under Battery Voltage interface, press SET button and hold on 5s then enter into the

interface of Battery type setting. After choosing the battery type by pressing MENU button,

waiting for 5s or pressing SET button again to modify successfully.

 Battery Type

①Sealed (Default)

NOTE: Please refer to the battery voltage parameters table for the different battery

type.

5. Protections

Protection

Conditions

PV Reverse

When the battery is correct connecting, the

Polarity

PV can be reversed.

Battery Reverse

When the PV is not connecting, the battery

Polarity

can be reversed.

Battery Over

The battery voltage reaches to the OVD

Voltage

Battery Over

The battery voltage reaches to the LVD

Discharge

Temperature sensor is higher than 65℃

Battery

Overheating

Temperature sensor is less than 55℃

7.Technical Specifications

Item

VS1024AU

Nominal system voltage

Battery input voltage range

Rated charge/discharge current

10A@55℃

Max. PV open circuit voltage

Battery type

Equalize Charging Voltage

※

Boost Charging Voltage

※

Float Charging Voltage

※

Low Voltage Reconnect

Voltage

※

Low Voltage Disconnect

Voltage

※

Self-consumption

Temperature compensation

coefficient

Charge circuit voltage drop

Discharge circuit voltage drop

LCD temperature range

Working environment

temperature

Relative humidity

Enclosure

Grounding

USB output

Overall dimension

142x85x41.5mm 160x94.9x49.3mm

Mounting dimension

130x60mm

Mounting hole size

Terminals

4mm

Net weight

※Above the parameters are in 12V system at 25℃, twice in 24Vsystem, triple in 36V system and quadruple in 48V system.

①

,Load short circuit

Timer 2

Disabled

Load will be on for 1 hour

before sunrise

Load will be on for 2 hours

before sunrise

Load will be on for 3～13

～

hours before sunrise

Load will be on for 14

hours before sunrise

Load will be on for 15

hours before sunrise

Disabled

②Gel

③Flooded

The controller is not

damage

Stop charging

Stop discharging

Output is OFF

Output is ON

VS2024AU

VS3024AU

12/24VDC

Auto

9V～32V

20A@55℃

50V

148x70mm

Φ4.5mm

/12AWG

10mm

/8AWG

0.22kg

0.35kg

Controller

Overheating

Load Short

Circuit

Load Overload

Damaged RTS

6. Troubleshooting

Faults

The

LCD

during daytime when

sunshine falls on PV

modules properly

Wire connection is

correct,

LCD

display

8. Disclaimer

Status

This warranty does not apply under the following conditions:

1) Damage from improper use or use in an unsuitable environment.

2) PV or load current, voltage or power exceeding the rated value of controller.

3) The controller is working temperature exceed the limit working environment

temperature.

4) User disassembly or attempted repair the controller without permission.

5) The controller is damaged due to natural elements such as lighting.

6) The controller is damaged during transportation and shipment.

VS3048AU

12/24/36/48VDC

Auto

9V～64V

30A@55℃

96V

Sealed(Default) / Gel / Flooded

Sealed:14.6V/ Gel: No/ Flooded:14.8V

Sealed:14.4V/ Gel:14.2V/ Flooded:14.6V

Sealed/Gel/Flooded:13.8V

Sealed/Gel/Flooded:12.6V

Sealed/Gel/Flooded:11.1V

≤9.2mA/12V;≤11.7mA/24V; ≤14.5mA/36V;≤17mA/48V

-3mV/℃/2V（25℃）

≤0.29V

≤0.16V

-20℃～+70℃

-25℃～+55℃(Product can work continuously at full load)

≤95%, N.C.

IP30

Common Positive

5VDC/2.4A(Total)

181x100.9x59.8mm

172x80mm

Φ5mm

16mm

/6AWG

0.55kg

0.58kg

Temperature sensor is higher than 85℃

Temperature sensor is less than 75℃

Load current ≥2.5 times rated current

One short circuit, the output is OFF 5s；

Two short circuit, the output is OFF 10s；

Three short circuit, the output is OFF 15s；

Four short circuit, the output is OFF 20s；

Five short circuit, the output is OFF 25s；

Six short circuit, the output is OFF

Load current ≥2.5 times rated current

1.02-1.05 times, 50s,

1.05-1.25 times, 30s

1.25-1.35 times,10s

1.35-1.5 times 2s

The RTS is short-circuited or damaged

Possible reasons

off

array

disconnection

1) Battery voltage is

lower than 9V

2) PV voltage is less

not

than battery voltage

Interface

Battery over voltage

blink

Interface

Battery

blink

over discharged

Interface

Battery Overheating

blink

Interface

Over load or Short

blink

circuit

VS4524AU

VS4548AU

12/24VDC

12/24/36/48VDC

Auto

9V～32V

9V～64V

45A@55℃

50V

96V

194x118.4x63.8mm

185x90mm

Φ5mm

16mm

/6AWG

0.76kg

0.88kg

Any changes without prior notice!

Output is OFF

Output is ON

Output is OFF

Clear the fault:

Restart the controller

or wait for one

night-day cycle

(night time>3 hours).

Output is OFF

Clear the fault:

Restart the controller

or wait for one

night-day cycle

(night time>3 hours).

Charging or

discharging at 25℃

Troubleshooting

Confirm that PV wire connections

are correct and tight

1) Please check the voltage of

battery. At least 9V voltage to

activate the controller

2) Check the PV input voltage

which should be higher than

battery's

Check if the battery voltage is

higher than OVD point (over

voltage disconnect voltage), and

disconnect the PV.

When the

battery

voltage

restored to or above LVR point

(low voltage reconnect voltage),

the load will recover

The controller will automatically

turn the system off. But while the

temperature decline to be below

50 ºC, the controller will resume.

Please reduce the number of

electric

equipments

check

carefully loads connection.

VS6024AU

VS6048AU

12/24VDC

12/24/36/48VDC

Auto

9V～32V

9V～64V

60A@55℃

50V

96V

214x128.7x72.2mm

205x100mm

Φ5mm

25mm

/4AWG

1.02kg

1.04kg

Version

number：V1.2