Axium Clinical Programmer Panduan Pengguna - Halaman 15
Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Peralatan Medis Axium Clinical Programmer. Axium Clinical Programmer 16 halaman.
Halaman CetakAppendix I: Programmable parameters and values
Parameter
Programmable Values
Pulse Amplitude
0 – 6000 µA
0-2000 µA (25 µA increments)
2000-6000 µA (50 µA increments)
Maximum Pulse Amplitude
Same as Pulse Amplitude
Pulse Width
40 – 720 µs (20µs increments)
Pulse Frequency
4 – 80 Hz (2 Hz increments)
Data Field
Selectable Values
Diagnosis
Abdominal Pain; Axial Low Back Pain; Axial Neck Pain; CRPS
(Primary and Secondary)
Type 1; CRPS Type 2; Diabetic Peripheral Neuropathy; FBSS;
FNSS; Lower Extremity Neuropathic Pain; Neuropathic Pain; Other;
Peripheral Neuropathy; Peripheral Vascular Disease; Phantom Pain;
Post-Herpetic Neuralgia; Post Surgical Pain; Radicular Arm Pain;
Radicular Leg Pain; Thoracic Pain; Upper Extremity Neuropathic
Pain; Visceral Pain;
Periodic Impedance Interval
Off; 30 s; 1 min; 5 min; 20 min; 30 min; 1 h; 6h; 12 h; 1 days; 3 days;
7 days; 10 days; 30 days
Lead Model Number
MN0300; MN0400, MN10350, MN10450, MN20350, MN20450
Stimulus Response Anatomy
Off; Neck; Shoulder; Scapula; Upper Back; Middle Back; Lower
Back; Back & Leg; Thigh; Knee; Lower Leg; Ankle; Foot(top);
Foot(bottom); Toes; Chest; Axilla; Ribs; Abdomen; Hip; Groin; Upper
Arm; Elbow; Forearm; Hands; Fingers
Stimulus Response Sensation Off; Burning; Buzzing; Cold; Comforting; Cramping; Heavy;
Massaging; Numb; Other; Pain; Paresthesia; Pressure; Relief;
Soothing; Spasm; Tapping; Tingling; Vibrating; Warm
Spine Location
L L1; R L1; L L2; R L2; L L3; R L3; L L4; R L4; L L5; R L5; L T1; R
T1; L T2; R T2; L T3; R T3; L T4; R T4; L T5; R T5; L T6; R T6; L T7;
R T7; L T8; R T8; L T9; R T9; L T10; R T10; L T11; R T11; L T12; R
T12; L S1; R S1; L S2; R S2; L S3; R S3; L S4; R S4; L S5; R S5; L
C1; R C1; L C2; R C2; L C3; R C3; L C4; R C4; L C5; R C5; L C6; R
C6; L C7; R C7; L C8; R C8
Magnet Turnoff Time
Off; 1 s; 2 s; 3 s; 4 s; 5 s; 6 s; 7 s; 8 s; 9 s; 10 s; 15 s; 20 s; 25 s;
30 s; 40 s; 50 s; 1 min; 70 s; 80 s; 90 s; 100 s; 110 s; 2 min
Ramp Duration
1 s; 2 s; 3 s; 4 s; 5 s; 6 s; 7 s; 8 s
Default
0 µA
0 µA
300 µs
20 Hz
25
Appendix II: Troubleshooting
Pop-up Messages
Condition
All stimulation has been
All stimulation turned off due to
turned OFF.
data corruption.
Cancelled Connect
Cancel was pressed with
Request
connecting attempt in progress.
Changes since last
Communication was lost prior
programming were lost
to programming attempt.
due to loss of connection
with the stimulator. Please
reconnect to stimulator.
Connected to stimulator.
All RF channels have noise
Communication is poor.
levels above the noise
threshold.
Connecting to stimulator...
"Connect" button on the main
menu was pressed.
Connection Established.
Connection attempt was
successful.
Connection with
Dropped RF connection.
stimulator was lost.
Please reconnect.
Do you want to program
A new Workspace or Exit button
changes?
was selected without saving
(programming) changes.
Invalid FCE password.
Invalid FCE password was
Please try again.
entered.
Lead N detected a
During an impedance
Current Too High
measurement, the measured
condition.
current was too high.
Lead N impedance of
Lead impedance is out of range
NNN Ω is out of range.
Maximum stimulation
Maximum stimulation output
output has been reached.
has been reached (4.6V).
The stimulator is in
hibernation.
Battery Voltage = xxx
Do you want to exit
hibernation?
Buttons
Resolution
"OK"
Contact your
Spinal Modulation
Representative.
"OK"
Reconnect to stimulator
and re-enter program
changes.
Try moving to an area with
fewer sources of noise.
"OK"
"OK"
"Yes"
"No"
"Cancel"
"OK"
Only Spinal Modulation
representatives should
access the FCE mode.
"OK"
Repeat measurement. If
problem reoccurs, contact
your Spinal Modulation
representative.
"OK"
Repeat measurement or
accept as is.
"OK"
Investigate lead integrity.
26