Olympus VN-7100 Petunjuk Manual - Halaman 7

Jelajahi secara online atau unduh pdf Petunjuk Manual untuk Perekam Suara Olympus VN-7100. Olympus VN-7100 11 halaman. Gravador digital de voz
Juga untuk Olympus VN-7100: Petunjuk (Bahasa Inggris) (11 halaman), (Bahasa Prancis) Mode D'emploi (11 halaman), Manual (Bahasa Portugis) (10 halaman)

Halaman Cetak

Microphone sensitivity [MIC]

[HI]: High recording sensitivity

suitable to record conferences and

lessons.

[LO]: Standard recording sensitivity

suitable for dictation.

• When you would like to clearly

record a speaker's voice, set [MIC]

to [LO] and hold recorder's built-in

microphone close to the speaker's

mouth (5-10 cm).

Variable Control Voice

Actuator [VCVA]

When the microphone senses

that sounds have reached a

preset threshold volume level,

the built-in Variable Control Voice

Actuator (VCVA) starts recording

automatically, and stops when the

volume drops below the threshold

level. The VCVA feature extends

recording time and conserves

memory by stopping recording

during silent periods, which helps

the playback to be more efficient.

[ON]: Enables the VCVA function.

[OFF]: Disables this function.

Adjust the start/stop actuation level:

If the surrounding noise is loud,

the starting sensitivity of the VCVA

can be adjusted according to the

recording situation.

1 Press the REC (s) button to start

recording.

• When the sound volume is lower

than the preset threshold sound

level, recording automatically stops

after approximately 2 seconds, and

[STANd-B y ] flashes on the display.

The recording indicator light turns

when recording starts and flashes

when recording pauses.

2 Press the + or − button to adjust

the start/stop actuation level.

• The VCVA level can be set to 15

different values.

• The higher the value, the more

sensitive the recorder will be to

sounds. At the highest value,

even the faintest sound will

activate recording.

• The start/stop actuation level also

varies according to the selected

microphone sensitivity mode.

• If the starting level is not adjusted

within 2 seconds, the display will

return to the previous one.

• To ensure successful recordings,

prior testing and adjustment of

the start/stop actuation level is

recommended.

Timer recording [TIMER]

[ON]: Enables the timer recording.

[OFF]: Disables this function.

1 Select [ON] and press the `OK

button.

• The "hour" will flash on the

display.

2 Press the + or − button to change

the setting.

Press the `OK or 9 button to

set.

• Repeat steps 2 and 3 to set the

starting "minute" and the ending

"hour" and "minute".

Press the + or − button to select

between [ONCE] and [DAIL y ].

[ONCE]: Records only once at the

specified time.

[DAIL y ]: Records every day at the

specified time.

5 Press the `OK or 9 button to

set.

• With this function, you can set only

the starting and the ending time

of recording. For the recording

mode, the microphone sensitivity,

VCVA and folders settings, the

settings selected before the timer

recording will be applied.

• If you set a timer recording that

could exceed the remaining

time capacity, [FULL] will flash

for 2 seconds. The setting will

be applied but the recording

will be interrupted. Delete any

unnecessary file.

• If the batteries run out while

recording based on the timer

setting, the recorder will stop

recording. Check the battery

power before starting the timer

recording.

Noise cancel [NOISE-C]

If the recorded audio is difficult

to understand because of noisy

surroundings, adjust the noise cancel

setting level.

[ON]: Noise will be reduced during

file playback to achieve a better

sound quality.

[OFF]: Disables this function.

Continuous playback

[ALL PLA y ] (For VN-7200 only)

[ON]: Plays file continuously in the

current folder until the last file and

then stops.

[OFF]: Plays file stops after playing

back the current file.

Repeat playback [REPEAT]

(For VN-7200 only)

[ON]: Plays the current file repeatedly.

[OFF]: Disables this function.

Skip space [SKIP]

(For VN-7200 only)

This function is convenient for

quickly skipping to another playback

position or to repeat the playback of

short phrases.

[ON]: While the recorder is during

playback, pressing 9 will make

the recorder forward skip 10 seconds,

while pressing 0 will make it

reverse skip 3 seconds.

[OFF]: The recorder will forward skip

or reverse skip a file.

• If there is an index mark or a cue

closer than the skip space, the

recorder will forward skip/reverse

skip to that position.

Alarm playback [ALARM]

You can use the alarm playback

function to sound the alarm tone

for 5 minutes at the scheduled time.

Within these 5 minutes, pressing any

button other than the POWER switch

will make the recorder playback

the preselected file. With the alarm

playback function, only one file can

be played back. Select a file for the

function before setting the time.