Axminster AW422J Panduan Pengguna - Halaman 5

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Alat Listrik Axminster AW422J. Axminster AW422J 8 halaman. 10-22mm narrow crown stapler

Halaman Cetak

Using your Air Stapler...

A X M I N S T E R

W H I T E

Using the Oil supplied in the small oiler bottle, put 2-3 drops into the air connector.

It is always a good policy to add at least a drop of oil to the tool prior to the first

use of the day, even if you have automatic oilers fitted to your supply system. If you

do not have inline oilers, put 2-3 drops of oil into the tool first thing and then add 2

drops every 1-2 working hours.

Connect the stapler to the hose line, check there are no leaks anywhere in the system.

Organise a couple of pieces of scrap timber, preferably from the offcuts of the job you are

doing, and the material to be stapled to it and staple the two? items together. Remember,

there is no 'contact safety' fitted to this tool,the stapler will fire when the trigger is pressed.

Carry out several trial staplings, and then check you are driving the staples to the correct

depth. If not, adjust the air pressure (up or down) and carry out more trials, until you are

satisfied. You may have to set the 'staple height setting plate' in order to limit how deeply

the staple is actually driven, e.g. you may require to fasten cloth/covering, et al., to a frame

work, and the material is not sufficiently robust to resist severing if the staple is driven

through it?

Maintenance...

Keep the tool clean, and free from any splashes that may be picked up from current work,

e.g. paint, glue ,etc.

Frequent but not excessive oiling is the key to keeping your air tools working properly.

Lack of oil and ingress of water will damage your air tools. If your air system is not fitted

with water traps and in line oilers, make sure that the tool is not allowed to run 'dry' or to

retain moisture.

Keep the tool stowed safely away when not in use. Do not allow sawdust et al., to ingress

the tool.

Good Working Practices/Safety

The following suggestions will enable you to observe good working

practices, keep yourself and fellow workers safe and maintain your

tools and equipment in good working order.

Work Place/Environment.

Keep the tool clean; it will enable you to more easily see any damage that may have occurred.

Clean the tool with a damp soapy cloth if needs be, do not use any solvents or cleaners, as these

may cause damage to any plastic components. Check the tool for damage both before and after work.

If damage has occurred, have it repaired by a suitably qualified person.

Check the air lines are undamaged, that supply galleries, spurs or connectors are not leaking.

Keep the work area well lit and uncluttered as is practical, this includes personnel as well as material.

Under no circumstances should CHILDREN be allowed in work areas.

It is good practice to leave the tool disconnected from the air supply until work is about to commence,

when it is not in use, or unattended. Once you are ready to commence work, remove any tools used

in the setting up operations (if any) and place safely out of the way. Re-connect the tool.

Carry out a final check e.g. the connector is tight 'on', the air lines are not leaking, any bits etc, fitted

to the tool are secure, check you have the correct pressure set, and if you require to move around

during the work operation, that air lines etc, will not 'snag'.

Make sure you are comfortable before you start work, balanced, not reaching etc.,

Few drops of oil

Wear the appropriate safety clothing, goggles, gloves, masks etc., If the work operation or

( PNEUMATIC OIL ONLY)

environment appears to be excessively noisy, wear ear-defenders. If you wear your hair in a long

style, wearing a cap, safety helmet, hairnet, even a sweatband, will minimise the possibility of your

hair being caught up in the moving parts of the tool, likewise, consideration should be given to the

removal of rings and wristwatches, if these are liable to be a 'snag' hazard. Consideration should also

be given to non-slip footwear, etc.

Do not work with cutting or boring tools of any description if you are tired, your attention is wandering

or you are being subjected to distraction. A deep cut, a lost fingertip or worse; is not worth it!

Do not work with power tools of any description, if you are currently taking medication, unless you

have ascertained that your medication will not cause your judgement or awareness to be impaired.

OIL

Do not use this tool within the designated safety areas of flammable liquid stores or in areas where

there may be volatile gases.

General Safety Instructions and Recommendations

whilst using Air Equipment...

KEEP TOOLS AND EQUIPMENT OUT

WARNING!!

OF THE REACH OF YOUNG CHILDREN

Air Powered Tools

A X M I N S T E R

W H I T E