Arcam Delta 70.2 Buku Pegangan - Halaman 8

Jelajahi secara online atau unduh pdf Buku Pegangan untuk Pemutar CD Arcam Delta 70.2. Arcam Delta 70.2 12 halaman. Arcam cd player and cd transport handbook
Juga untuk Arcam Delta 70.2: Buku Pegangan (12 halaman)

Halaman Cetak

Playing a complete disc

The complete disc may be played in one of the following

ways:

(a) If the disc is not loaded: open the drawer, load the disc

and press the PLAY button (4).

(b) If the LOAD button (3) is pressed instead of the PLAY

button (4), then the disc information (number of tracks + total time} may

be read before pressing the PLAY button (4).

(c} If the disc is already loaded in the machine: simply press

the PLAY button [4].

The disc may be stopped at any time by pressing the STOP

button (5). If this is done then the player will revert to playing the disc

from the beginning again when the PLAY button (4) is next pressed.

Playing from a specific track

Load the disc and then select the desired track number by

pressing the TRACK buttons (9) and (10] to decrement or increment the

TRACK display (B), until the desired track number is shown. [These

buttons may either be pressed repeatedly or held down for a steady

count, as desired].

You can simplify this operation by using the 0—9 direct entry

keypad on the CRTO remote control handset (see below).

Replay

To restart a track which is already playing, simply press the

PLAY button (4). This will replay the track from the beginning.

Holding Play/Interrupting Play

Pressing the PAUSE button (6) while playing will interrupt

play and mute the output. The laser head will continue to track the disc

at the precise point of interruption until the PAUSE button [6] is pressed

again, when the program will start from exactly the same point.

Whenever the player is in the pause mode the PAUSE header

on the left of the display will be illuminated.

Cueing and Searching

In order to cue the laser head silently to an exact (known)

point on the disc, load the disc, press the PLAY button (4) and the press

the PAUSE button (6) as soon as the first track is ready to play (indicated

by TRACK-OT

on the display]. Select the track required by using the

TRACK controls (9) and (10). Then use the SEARCH buttons (7) and (8) to

arrive at the exact timing point required. Press the PAUSE button (6)

when you are ready to start playing.

The above process allows you silently to access

a known

place on a disc (track and elapsed time on that track) to an accuracy of

one second. The same process can be carried out with audible cueing by

omitting to use the PAUSE function.

Note that the SEARCH process has three operational speeds

dependent on how long the SEARCH buttons {7} and (8) are kept

depressed.

Programming

The Arcam Delta CD machines can be programmed to play

up to 20 pre-selected tracks from a disc in any order. Each track can be

anywhere in the range 1—929. (NOTE — although tracks in the range

1—99 can be programmed, only those in the range 1-26 give a time

indication on the display].

Programming must be carried out with the disc loaded, so

that the player first knows the actual number of tracks recorded on the

disc. It is not possible to program index points, although they do remain

accessible from the remote control handset during the play of a program,

except when you have programmed only one track number.

To store the track numbers you want to include in a program,

refer to the disc holder and bring up each track number in turn using the

TRACK buttons (9) and (10) to move up or down through the track

numbers, whichever is quickest. !t is of course even quicker to use the

0—9 direct entry key pad on the CR10 handset (see below). The TRACK

display header below the track number will flash on and off. You can

then store a track by pressing the PROGRAM button (11). When a track

has been stored the TRACK header will stop flashing and the PROGRAM