Arcam fmj UDP411 Buku Pegangan - Halaman 6

Jelajahi secara online atau unduh pdf Buku Pegangan untuk Pemutar Blu-ray Arcam fmj UDP411. Arcam fmj UDP411 13 halaman. Blu-ray disc player arcam fmj udp411

Halaman Cetak

basic

operation

Introduction

Loading a disc

Press

on the front panel (or

on the handset)

'Basic operation' explains how to play a Blu-ray Disc

(BD), DVD, SACD, CD or other type of disc. Note that

and place the disc on the tray, with the playback side

facing down (some discs are double sided, in which case

it may be necessary to configure your player correctly

for your system before optimum – or any – playback can

the side labelled 'side A' should face up to play side A).

be achieved. Player configuration is described beginning

Press

on the front panel to close the tray. The disc

on page E-16.

loads after a pause of a few seconds.

More sophisticated features – such as special playback

Playing a disc

modes and programming jumps and playback sequences

– are described in the 'advanced operation' section, later

A disc may take some time to load once the tray is

in this handbook.

closed. When the 'Optical Disc Autoplay' setting is set to

On (the default setting), playback starts automatically.

Switching on

(For details, refer to 'Optical Disc AutoPlay' on page

Switch the unit on by pressing the

button. The

E-17).

POWER

status LED glows green when the unit is powered up and

If Autoplay is set to Off, the player's Main Menu will

red when in standby mode. The remote control is used

appear on your TV. Use the cursor keys to select the disc

to enter and exit standby mode. If the

button is

POWER

, then press

to start playback.

MY MEDIA

pressed (or power is removed) whilst in standby, the

Some titles begin by displaying a menu. Select the menu

unit will enter standby mode when power is re-applied.

item 'Play movie' (or similar) using the cursor pad, then

Note that the remote control sensor is located on the

press

to start playback.

right-hand side of the display window. Do not obstruct

For discs that do not play automatically, press

this or the remote control will not work.

the front panel or press

on the remote control.

Fast play

NOTE

Press

on the front-panel or remote control to

When you press a button, if the unit does not accept

play fast forwards or backwards. The following speeds

its operation,  appears on the TV screen.

for fast playback are available: x2, x4, x8, x16 or x32

(depending on disc type). Press the button repeatedly

Invalid operation may also occur if:

to cycle through the different speeds. To resume normal

The region codes of the unit differs from that

playback speed, press

PLAY

of the disc, so playback is not allowed.

The parental control is set to prevent

Skipping chapters/tracks

operation: see 'Security/Parental Control' on

To skip chapters (or tracks on a CD), press

page E-18.

When skipping back, the first button press takes you to

Some operations may be prohibited due to

the beginning of the current chapter. Pressing the button

disc manufacturer's settings.

again takes you to the start of the previous chapter.

Pausing playback

Press

;

on the front panel or

;

on the remote

control to pause playback. To resume playback, press

;

on the front panel or

on the handset.

Stopping playback

Press the

button on the front panel or

on the

;

remote control to stop playback.

When playing a BD/DVD, pressing

once performs

a 'resume stop' . If you now press

, playback resumes

from the point it was stopped.

If you press

on the front panel or

on the remote

control twice, this is a 'complete stop' , and playback

resumes from the beginning of the disc.

E-10

remote

control

The UDP411 is supplied with the CR301 backlit remote

control.

Using the remote control

Please keep in mind the following when using the

remote control:

Ensure there are no obstacles between the

remote control and the remote sensor on the

front panel. The remote has a range of about 7

metres. (If the remote sensor is obscured, the IR

in remote control input jack on the rear panel is

available. Please consult your dealer for further

information.)

Remote operation may become unreliable if

strong sunlight or fluorescent light is shining on

the remote sensor of the unit.

Replace the batteries when you notice a reduction

in the operating range of the remote control.

Inserting batteries into the remote control

Open the battery compartment on the back of the

handset.

Insert two ' A AA' batteries according to the

diagram on the battery cover casing.

Slide the battery cover casing back into position

and lock it closed with a click.

Backlight

A backlight comes on for five seconds whenever a key

is pressed. This helps you use the handset in subdued

lighting conditions.

NOTE

The CR301 remote complies with Part 15

of the FCC rules

Incorrect use of batteries can result in hazards

such as leakage and bursting.

This equipment has been tested and found to comply

with the limits for a class B digital device, pursuant to

Do not mix old and new batteries together.

part 15 of the FCC Rules. These limits are designed

Do not use non-identical batteries together

to provide a reasonable protection against harmful

– although they may look similar, different

interference in a residential installation. This

batteries may have different voltages.

equipment generates, uses, and can radiated radio

Ensure the plus (+) and minus (–) ends of

frequency energy and if not installed and used in

each battery match the indications in the

accordance with the instructions, may cause harmful

battery compartment.

interference to radio communications. However,

Remove batteries from equipment that is not

there is no guarantee that interference will not occur

going to be used for a month or more.

in a particular installation. If this equipment does

When disposing of used batteries, please

cause harmful interference to radio or television

comply with governmental or local regulations

reception, which can be determined by turning the

that apply in your country or area.

equipment off and on, the user is encouraged to try

to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver.

Connect the equipment into an outlet or a circuit

different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV

technician for help.

E-11