Epson C11C418001 - Stylus C60 Inkjet Printer Panduan Pengguna - Halaman 7
Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Printer Epson C11C418001 - Stylus C60 Inkjet Printer. Epson C11C418001 - Stylus C60 Inkjet Printer 11 halaman. Ink jet printer
Juga untuk Epson C11C418001 - Stylus C60 Inkjet Printer: Baca Panduan Pertama Ini (12 halaman), Mulai di sini (4 halaman), Spesifikasi (2 halaman), Pernyataan Kesesuaian (2 halaman)
Halaman Cetak
6. Press down firmly on the ink cartridge clamp until it snaps
in place.
7. If you need to replace the other ink cartridge, repeat steps 2
through 6 before continuing with step 8.
8. Press the e ink replacement button and close the printer
cover. The printer begins charging the ink delivery system.
9. Wait until ink charging is finished (the P power light stops
flashing and the red b error light goes out).
Cleaning the Print Head
If your printouts are unexpectedly light or faint, or dots or
lines are missing from the image, you may need to clean the
print head. This unclogs the nozzles so they can deliver ink
properly. Print head cleaning uses ink, so clean it only if
quality declines.
This section explains how to clean the print head using the
Head Cleaning utility. This is the recommended method
when the printer is connected directly to your computer (not
over a network).
You can also clean the print head by holding down the
b maintenance button on the printer's control panel for three
seconds when the red b error light is off. See the Print Show
movies or electronic Reference Guide for detailed instructions.
When you don't turn on your printer for a long time, the
print quality can decline. It's a good idea to turn on your
printer at least once a month to maintain good print
quality.
Running the Head Cleaning Utility
1. Make sure the printer is turned on but not printing, and the
red b error light is off. (If the red light is flashing or on,
you may need to replace the ink cartridge; see page 6 for
details.)
2. Do one of the following:
❏ Windows: right-click the
the right side of the Windows taskbar. Then click
.
Cleaning
❏ Macintosh: Open the File menu and choose
or
Setup
Print
the
Head Cleaning
3. Follow the instructions on the screen to clean the print
head. Cleaning takes about 30 seconds, during which the
printer makes some noise and the green P power light
flashes.
Never turn off the printer while the
flashing, unless the printer hasn't moved or made noise
for more than 5 minutes.
4. When the green P power light stops flashing, run a nozzle
check to confirm the print head nozzles are clean.
Make sure plain paper (not special ink jet paper) is loaded
in the printer and click
click
. The nozzle check pattern prints (see the next
Print
section for details).
5. If the nozzle check pattern has no gaps or lines, click
If the pattern has white lines, click
head again.
If you don't see any improvement after cleaning three or
four times, check the solutions in your Printer Basics book.
You can also turn the printer off and wait overnight—this
allows any dried ink to soften—and then try cleaning the
print head again.
Examining the Nozzle Check Pattern
Examine the nozzle check pattern you print. Each black and
colored area should be complete, with no gaps or lines, as
shown below:
❏ If your printout looks okay, you're done.
❏ If any dots or lines are missing (as shown below), clean the
print head again; see the previous section for instructions.
7/01
EPSON Stylus C60
Status Monitor 3 icon on
. Click the
button, then click
Utility
button.
P
power light is
Print Nozzle Check Pattern
to clean the print
Clean
EPSON Stylus C60
Head
Page
. Then
.
Finish
- 7