Epson DFX-8500 - Impact Printer Informasi Produk - Halaman 6

Jelajahi secara online atau unduh pdf Informasi Produk untuk Printer Epson DFX-8500 - Impact Printer. Epson DFX-8500 - Impact Printer 15 halaman. Warranty statement
Juga untuk Epson DFX-8500 - Impact Printer: Brosur & Spesifikasi (24 halaman), Spesifikasi (2 halaman), Garansi Terbatas (2 halaman)

Halaman Cetak

EPSON DFX-8500

Pitch

Selects the characters per inch for

printing. Press the button until the light

appears next to the desired pitch. (Your

software setting overrides this setting.)

Copy

Lets you print the document darker. This

button is available in SuperDraft and

Draft mode only and is disabled if you

use the status monitor utility and select a

paper number from 1 to 8.

When the top cover is open, lets you

TOF

(Top of Form)

enter and exit the top-of-form mode to

adjust the top-of-form position.

If your printing begins too high or low on

the page, you can reset the top-of-form

position by entering top-of-form mode

and using micro feed to adjust the

position. The printer remembers this new

top-of-form position even after it is

turned off, reset, or initialized. Also, the

printer remembers separate top-of-form

positions for the front and rear tractors.

Tear Off

Feeds the paper to the printer's tear-off

edge and puts the printer in tear-off

mode.

If the perforation on your paper does not

align exactly with the printer's tear-off

edge, use the

adjust the tear-off position.

This button can also be used to run the

printer's NLQ self test.

CAUTION:

Never press the Tear Off button when labels are loaded in the

printer. Use the LF/FF Load button to feed the printed labels to

a point where they can be torn off

LF/FF Load

advances paper one line at a time. To

feed your paper forward one line, press

this button once.

advances continuous paper to the top

of the next page. Press and hold the

button for about one second.

Load loads paper on the push tractor of

the selected paper path when no paper is

currently loaded.

6 - EPSON DFX-8500

buttons to

Micro Feed

CAUTION:

When labels are loaded, use only the top Micro Feed button.

Never feed labels backward through the printer.

Pause

Tractor Select

Front/Rear

CAUTION:

Never use the Front/Rear button when labels are loaded in the

printer. Always tear off any printed pages or excess paper so

you don't feed more than one page backward through the

printer.

5/98

This button can also be used to run the

draft self test.

These two buttons advance or reverse the

loaded paper in 1/216-inch increments.

The top button advances the paper and

the bottom button reverses it. You can

use these buttons to adjust the top-of-

form, tear-off, and printing positions.

To reset the top-of-form position, press

the

button to enter top-of-form

TOF

mode. Then use the

Micro Feed

to move the paper to the desired position.

To reset the tear-off position, press the

button to enter tear-off mode

Tear Off

and feed the paper to the tear-off

position. Then use the

Micro Feed

buttons to move the paper to the desired

position.

To adjust the printing position, press

either

button to advance or

Micro Feed

reverse the paper to the desired position.

Press to temporarily stop printing. Press

again to resume printing.

Hold down for at least 3 seconds to reset

the printer's control panel settings.

Selects the front or rear tractor. If you

have been using paper loaded on one

tractor, first remove the printed output

before pressing this button to switch the

tractor. When you switch between

tractors, the paper already loaded in the

printer is fed backward to the standby

position, and the paper on the newly

selected tractor is loaded.

buttons