ArchiTech SC-502E Panduan Instalasi

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Pembicara ArchiTech SC-502E. ArchiTech SC-502E 2 halaman. Stereo loudspeaker for: 5-1/4, 6-1/2" & 8" in-ceiling

Halaman Cetak

Congratulations! You have purchased a high quality stereo

loudspeaker. When matched to comparable electronic

equipment, expect years of quality high fidelity sound. Our

belief is that music matters and we are focused on delivering

superlative music reproduction everywhere in your home.

The following manual is designed to give you, the installer

or owner, basic information as to the speaker's installation

and operation. It is beyond the scope of this manual to go

into all the details that must be taken into consideration in

a sophisticated high fidelity system. When installing the

wiring and speakers it is important to adhere to all local

codes and regulations. Consulting a professional can help to

maximize your system's performance.

If you have any questions regarding this speaker which are

not answered by this manual, contact your local dealer for

assistance. For the most current information please visit

www.oemsystems.com.

MINIMUM TOOLS REQUIRED

# 2 Phillips Head Screw Driver / Drill Driver

Wire Cutter / Stripper

Other Possible Tools

Tape Measure, Pencil, Ladder, Drywall Saw, Stud-Finder, etc.

GENERAL DESCRIPTION

These two-way speakers have specially designed woofers

with linear long throw butyl rubber surrounds for long life and

superior damping. Dome tweeters are utilized for excellent

high frequency dispersion throughout your entire listening

environment.

SHIPPING DAMAGE

Each speaker is thoroughly tested before it leaves the

factory. However, in shipment, accidents may occur. Please

inspect your speakers carefully when you receive them to

make sure there is no damage. If there is, please notify your

dealer or supplier immediately for assistance. If you received

your speakers by public transportation, report the damage

immediately to the shipping company.

AMPLIFIER OPERATION

These speakers will perform well with amplifiers from 5 to

125 Watts RMS. However, damage to the speakers can

be done by amplifiers of nearly any power rating if the

amplifier is overdriven into clipping. "Amplifier clipping"

is a phrase used to describe a condition when, because of

the volume demand, an amplifier is being asked for more

power than it can give. Clipping causes distortion of the

audio signal. If you should hear an unusual amount of

distortion at high listening levels then consider reducing

the volume. DAMAGE DONE TO A SPEAKER BY CLIPPING IS

NOT COVERED UNDER THE WARRANTY.

Install Guide Rev. F

For: 5-1/4, 6-1/2"& 8"In-Ceiling

SPEAKER PLACEMENT

Placement of in-ceiling and in-wall speakers should be

carefully considered. Please contact a professional for

assistance if you are uncomfortable with the planning or

installation process.

Ideally, the speakers should be located where they will

provide the best possible sound and ease of installation. It

is beyond the scope of this publication to discuss all of the

various aspects of speaker placement, but here are some

helpful suggestions.

For the front channels of a home theater we recommend that

the speakers be placed between 18 and 36 inches (0.45m

to 0.9m) from an adjacent wall/surface, as measured to the

center of the hole. Avoid placing the speakers less than 12

inches (0.3m) from an adjacent wall. When placing speakers

near a corner, avoid locating them an equal distance from the

two adjacent surfaces.

If the drywall has not yet been installed, rough-in-kits are

available to reserve the speaker location. The hole is then cut

when the drywall is installed.

WIRING

To achieve maximum performance we recommend that the

speaker cable be at least 16 gauge or larger for runs over 50

feet (15m) and that the cable be double insulated. A CL-2 or

CL-3 rated cable may be required. Check local codes. "Zip

cord," which is single insulated and is often made with clear

insulation, should be avoided as it is not as durable. Allow

about 2½ feet (0.8m) of free cable at the speaker cut-out and

sufficient length at the other end to reach the electronics.

Having to add extra cable later can be tedious and time

consuming.

Avoid bundling speaker cables parallel to electrical cables

for extended lengths. Though the impedance is low and the

likelihood of interference low, this may help reduce hum and

RF interference. When securing the cable, use care not to

staple or nail through the electrical conductors. Doing so

could result in a short that might damage the electronics.

When connecting your speakers, make sure proper polarity

(phasing) is maintained. Simply put, this means ensuring the

same wire which is connected to the positive terminal of the

amplifier has its other end connected to the positive terminal

Overall

SC-520 KE

7-1/2" round

SC-502E

7-1/2" round

SC-602E

8-3/8" round

SC-62

8-3/8" round

SC-802E

9-3/4" round

Cut-Out (Round x Depth)

6-1/2" x 2-3/8"

7-3/8" x 2-7/8"

8-5/8" x 3-3/8"

page 1 of 2