Archos 97 Carbon Buku Petunjuk - Halaman 7
Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Tablet Archos 97 Carbon. Archos 97 Carbon 14 halaman.
Juga untuk Archos 97 Carbon: Manual (14 halaman)
Halaman CetakARCHOS 97 Carbon English
The ARCHOS will scan automatically for available WiFi networks and show all the wireless networks in range of your device.
The list is refreshed continuously.
5. Tap the network you want to connect to. Networks shown with the icon are secured connections.
A password is required for a secured connection.
6. Enter the required network information* and then tap on Connect.
network parameters you entered.
* For free access WiFi points, there is no need to enter any special information. For secured networks, you will need either a key (a series of numbers and/or letters) of the type WEP,
WPA, or WPA2, or you will need to have a WiFi access point that uses the WiFi protection standard WPS (WiFi Protected Setup). Check with the Internet service provider to obtain
the exact connection parameters required.
Note: When you are not connected to any WiFi network and you pass by a WiFi network, you receive a notification.
Advanced Connection
To manually scan for available WiFi networks,
1. Go to the WiFi settings screen.
2. Tap on Scan.
If the WiFi network you want to connect to does not appear in the list.
1. Tap on Add network.
2. Enter the required settings.
3. Tap on Save.
To access the advanced network parameters (Regulatory domain, IP address, etc),
1. Tap on the Menu button
in the upper right corner.
2. Tap on Advanced.
Other parameters will appear: the required information can be obtained from the Internet service provider.
WiFi connection problems
The ARCHOS tablets support the 802.11 b, g, and n WiFi protocols. If you cannot connect to your access point, first determine if the problem lies with your access point or with the
ARCHOS. Try using another WiFi device, such as a laptop computer or a WiFi enabled telephone and see if that will connect to your access point. If it does, then use the same WiFi
connection settings that it has on your ARCHOS. You could also try connecting your ARCHOS to a friend's WiFi network and if this works, change your access point parameters to
similar ones.
Possible solutions
Make sure you are not far from the WiFi hotspot.
Update the firmware of the device: http://www.archos.com/support.
Reset and redefine your connection parameters.
Check your WiFi router/modem documentation to see if it has a pairing button that needs to be pressed. Some modems have such a button that must be pressed the very first
time you try to make a WiFi connection with a new device.
If you have to enter a password (a security code of type WEP or WPA) be very careful that you do not confuse a 1 and I (one and letter "I"), a 0 and O (zero and letter "O"), or U
and V. These are common mistakes.
When entering a security code for your WiFi access, check the box Show password which will allow you to see exactly what you are typing in. This will avoid any mistakes.
Some access points use what is known as MAC filtering. That means, the WiFi access point has a list of access numbers (every hardware device has a unique MAC number)
which are the only ones allowed to access to the WiFi point. The person managing the WiFi modem/router should shut off this MAC filtering system to see if this solves the
problem. It is recommended to shut off MAC filtering in general as this is now known to be an outdated and ineffective system for WiFi security. If you must use it, you can find
your device's specific MAC address by going to Settings > Wireless & Networks > WiFi settings > Menu > Advanced. It will look something like 00:16:dc:5e:9e:39.
http://www.archos.com/manuals/A97Carbon_EN.htm
Your ARCHOS will now attempt to establish a connection to that WiFi access point with the
Page 7 of 14
2012-11-19