Cres Cor RO151033 Panduan Pemasangan, Pengoperasian, dan Pemeliharaan - Halaman 4
Jelajahi secara online atau unduh pdf Panduan Pemasangan, Pengoperasian, dan Pemeliharaan untuk Peralatan Makanan Komersial Cres Cor RO151033. Cres Cor RO151033 11 halaman. 8kw rethermalizers
Halaman Cetak
FL-RO151033
Rethermalizer
Page 4 of 11
Rev. 3 (5/14)
POWER
ON/OFF
FIRST-TIME OPERATION
NOTE: A new cabinet needs to "burn off" manufacturing
oils and excessive adhesive before its first use.
Do NOT load food until this has been done!
1 . Push the POWER button on; the light will come on.
NOTE: The letters "LOTPR" (low temperature) will
show on the control display until it reaches 140°F
(60°C) .
2 . Press the COOK button .
3 . Turn the SET control knob to show 350°F . Push the
SET knob to set the temperature .
4 . Push the HOLD button . Turn the SET knob to 150°F
(65°C) . Push the SET knob to set the temperature .
5 . TIME button will illuminate . Turn SET knob to one
(1) hour . Push the SET knob to set the time .
6 . Push START button . Control will display "PREHT",
then in approximately 15 minutes "READY" .
7 . Push START button again to begin the cooking/burn
off process .
8 . Turn the unit off and let cool . (Open door)
9 . Wipe the inside clean with detergent and hot water .
HOW TO USE THE RETHERM CONTROL:
*Push the POWER ON/OFF switch on the control panel;
the light will come on and the cabinet will start heating .
*The display will read "LOTPR" (low temperature)
below 140°F . (60°C .) .
NOTE: Wait half (1/2) hour after start up before loading
the food for best results .
The display will read "PREHT" until the cabinet
reaches the set temperature .
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
OPERATING INSTRUCTIONS
DISPLAY
COOK BUTTON
HOLD BUTTON
TIME
BUTTON
PROBE
BUTTON
5925 Heisley Road • Mentor, OH 44060-1833
CONTROL
SET KNOB
Retherm
+
START
BUTTON
RECIPE
DISPLAY
BUTTONS
BUTTON
Cooking/Retherming:
1 . Press the COOK button .
2 . Turn the SET knob to the desired cooking temperature
between 200°F (93°C) and 250°F (121°C) or 350°F
(176°C) .
3 . Push the knob to set the temperature .
4 . The control automatically goes to the HOLD mode .
(Continue to step 1 below) .
Holding:
(Press the HOLD button only if you are just holding food),
1 . Turn the SET knob to the desired holding temperature
between 140°F (60°C) and 220°F (104°C) .
2 . Push the SET knob to accept the temperature .
3 . The control automatically goes to the TIME mode .
Setting the time or Food Probe:
1 . If NOT using the Food Probe:
a) Turn the SET knob to the desired hours/minutes .
b) Push the SET knob to accept the time .
2 . Using the Food Probe:
Plug in the food probe BEFORE you enter the TIME
mode . Otherwise, you have to press the PROBE
button to set the probe temperature .
a) Turn the SET knob to the desired internal temperature .
b) Push the SET knob .
3 . Press the START button . The display will show
"PREHT", then "READY" when cooking temperature
is reached .
4 . Insert food probe into food, then load the cabinet and plug
food probe into unit .
5 . Once loaded, press the START button again .
Note: Press and hold the SET knob for 5 seconds to
cancel any recipe and clear the control .
FOOD PROBE
CONNECTOR