Cisco 3560V2 - Catalyst 48 10/100 Poe Lembar data - Halaman 12
Jelajahi secara online atau unduh pdf Lembar data untuk Beralih Cisco 3560V2 - Catalyst 48 10/100 Poe. Cisco 3560V2 - Catalyst 48 10/100 Poe 20 halaman. Cisco catalyst 3560v2-24ps: specifications
Halaman Cetak
availability of your network. LMS supports over 400 different device types, including Cisco Catalyst 3560 v2 series
switches, and it provides the following features:
Network discovery, topology views, end-station tracking, and VLAN management
●
Real-time network fault analysis with easy-to-deploy device specific best-practice templates
●
Hardware and software inventory management, centralized configuration tools, and syslog monitoring
●
Network response time and availability monitoring and tracking
●
Real-time device, link, and port traffic management, analysis, and reporting
●
For further details about CiscoWorks LMS, go to www.cisco.com/go/lms.
●
Table 2 describes switch hardware, Table 3 describes power specifications, Table 4 describes management and
standards support, and Table 5 describes safety and compliance.
Table 2.
Description
Performance
Connectors and Cabling
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Cisco Catalyst 3560 v2 Series Switch Hardware
Specification
Forwarding bandwidth
Flash memory
Max VLANs
VLAN IDs
Switched Virtual Interfaces (SVIs)
Maximum transmission unit (MTU)
Jumbo frames
MAC, routing, security, and QoS scalability numbers depend on the type of template used in the switch.
MAC address
IGMP groups and
multicast routes
Total unicast routes
Directly connected
hosts
Indirect routes
Security ACEs
QoS ACEs
PBR ACEs
● 10BASE-T ports: RJ-45 connectors, two-pair Category 3, 4, or 5 unshielded twisted-pair (UTP) cabling
● 10BASE-T PoE ports: RJ-45 connectors, two-pair Category 3, 4, or 5 UTP cabling power pins 1,2 (negative) and
3,6 (positive)
● 100BASE-TX ports: RJ-45 connectors, two-pair Category 5 UTP cabling
● 100BASE-TX PoE ports: RJ-45 connectors, two-pair Category 5 UTP cabling, power on pins 1,2 (negative) and 3,6
(positive)
● 1000BASE-T SFP-based ports: RJ-45 connectors, four-pair Category 5 UTP cabling
● 1000BASE-SX, -LX/LH, -ZX, and CWDM SFP-based ports: LC fiber connectors (single/multimode fiber)
● Cisco Catalyst 3560 SFP Interconnect Cable: two-pair shielded cabling, 50 cm
● Management console port: RJ-45-to-DB-9 cable for PC connections; for terminal connections, use RJ-45-to-DB-25
female data-terminal-equipment (DTE) adaptor (can be ordered separately from Cisco; part number ACS-
DSBUASYN=)
Default Template
Access Template
6K
4K
1K
1K
8K
6K
6K
4K
2K
2K
1K
2K
0.5K
0.5K
0
0.5K
32 Gbps
32 MB
1K
4K
Up to 1000
Up to 9000 bytes
9016 bytes
VLAN Template
12K
1K
0
0
0
1K
0.5K
0
Data Sheet
Routing Template
3K
1K
11K
3K
8K
1K
0.5K
0.5K
Page 12 of 20