Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Panduan Konfigurasi - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Konfigurasi untuk Beralih Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 8 halaman. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Juga untuk Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion: Catatan Instalasi (14 halaman), Panduan Solusi (17 halaman), Catatan Instalasi (46 halaman), Buku Putih (19 halaman), Deskripsi (1 halaman), Buletin Produk (6 halaman), Pemberitahuan (4 halaman), Lembar data (9 halaman), Lembar data (18 halaman), Buku Putih (18 halaman), Catatan Instalasi (28 halaman), Panduan Pemecahan Masalah (11 halaman), Catatan Instalasi (18 halaman), Panduan Pengguna (17 halaman), Catatan Instalasi (24 halaman), Manual (19 halaman), Catatan Instalasi (36 halaman)

Using the Bootflash or Bootdisk on a Supervisor Engine 720

All 12.2SX releases support the Supervisor Engine 720 64-MB bootflash device (sup-bootflash:).

Release 12.2(18)SXE5 and rebuilds and Release 12.2(18)SXF and rebuilds support WS-CF-UPG=,

which replaces the bootflash device with a CompactFlash adapter and 512 MB CompactFlash card

(sup-bootdisk:). Refer to this publication:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_17277.html

Using the Slots on a Supervisor Engine 720

The Supervisor Engine 720 has two CompactFlash Type II slots. The CompactFlash Type II slots

support CompactFlash Type II Flash PC cards sold by Cisco Systems, Inc. The keywords for the slots on

the active Supervisor Engine 720 are disk0: and disk1:. The keywords for the slots on a redundant

Supervisor Engine 720 are slavedisk0: and slavedisk1:.

Configuring Supervisor Engine 720 Ports

Supervisor Engine 720 port 1 has a small form-factor pluggable (SFP) connector and has no unique

configuration options.

Supervisor Engine 720 port 2 has an RJ-45 connector and an SFP connector (default). To use the RJ-45

connector, you must change the configuration.

To configure port 2 on a Supervisor Engine 720 to use either the RJ-45 connector or the SFP connector,

perform this task:

Command

Step 1

Router(config)# interface gigabitethernet slot/2

Step 2

Router(config-if)# media-type {rj45 | sfp}

Router(config-if)# no media-type

This example shows how to configure port 2 on a Supervisor Engine 720 in slot 5 to use the RJ-45

connector:

Router(config)# interface gigabitethernet 5/2

Router(config-if)# media-type rj45

Configuring

and Monitoring the Switch Fabric Functionality

These sections describe how to configure the switching mode and monitor the switch fabric functionality

that is included on a Supervisor Engine 720:

•

Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide, Release 12.2SXF

4-2

Understanding How the Switch Fabric Functionality Works, page 4-3

Configuring the Switch Fabric Functionality, page 4-4

Monitoring the Switch Fabric Functionality, page 4-4

Chapter 4

Purpose

Selects the Ethernet port to be configured.

Selects the connector to use.

Reverts to the default configuration (SFP).

Configuring a Supervisor Engine 720

OL-3999-08