Fibar Group FGS211 Panduan Pengoperasian
Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Beralih Fibar Group FGS211. Fibar Group FGS211 2 halaman. Relay switch
Halaman Cetak
ENG
I GENERAL INFORMATION ABOUT FIBARO SYSTEM
FIBARO provides many advantages when compared to similar
systems. In general, radio systems create a direct connection
between the receiver and transmitter. But the radio signal is
weakened by various obstacles located on its path (apartment walls,
furniture, etc.) and in extreme cases it fails to transfer required data.
The advantage of FIBARO system is that its devices apart from
being transmitters and receivers of signals, they are also a signal
"duplicators". When a direct connection path between the transmitter
and the receiver can not be established, the connection may be
achieved through other intermediate devices.
OPERATING MANUAL
is not only sent to the receivers but also the receivers send the
RELAY SWITCH
confirmation of its reception. This operation confirms their status so
FGS211 v1.4.
to check whether they are active. Safety of the FIBARO system
transmission is comparable to the safety of transmission in data bus
wired systems.
Remotely Controlled Relay Switch of FIBARO system is designed to
frequency. Every FIBARO system has its own unique identification
operate i n a w all s witch b ox, w all s ocket b ox o r i n l ocations w here t he
number (home ID). Therefore, it is possible to operate two or more
control of an electric device (up to 3kW) is needed. It is also possible
independent systems in one building without any interference.
to send a signal to any system that is to be integrated with Fibaro
system.
technology, guaranteeing their compatibility. This means that the
Specifications
system is open and it may be extended in the future. Find more
information at www.fibaro.com.
Power supply
FIBARO generates a dynamic network structure. After FIBARO
system is switched on, the location of its individual components is
Rated load current for A C
output
signals received from devices operating in a "mesh" network.
Rated load current for DC
output
using radio waves, controllers and a push button directly connected
Output circuit power
3 kW
to Fibaro Switch.
(resistive load)
Comply with EU standards
II Assembling Fibaro Switch
Temperature limits
Operational temperature
For installation in boxes
Radio protocol
Radio Frequency
Range
up to 30 m indoors
1. Before installation ensure that the voltage supply is
(depending on building materials)
disconnected.
2. Connect Fibaro switch as shown on the diagram
Dimensions (H x W x D)
3. Place the switch in the electrical box
4. Arrange the antenna (tips are presented below diagrams)
* In case of load other than resistive, pay attention to the value of
single switch
Technical Information
DANGER
Danger of electrocution! All works on the device
may be performed only by a qualified and licensed
electrician. Observe national regulations.
single switch
- option with an alternative power supply for the load
DANGER
Danger of electrocution. Even when the device is
turned off, voltage may be present at its terminals.
Any
works
introducing
changes
into
the
configuration of connections or the load must be
always performed with disconnected voltage
(disable the fuse).
TIPS
i
Do not connect the device to loads exceeding
recommended values.
Connect only in accordance with the diagram
presented i n t he m anual. I mproper c onnections m ay
be dangerous.
double switch
L
N
S1 S2
B
double switch
- option with an alternative power supply for the load
L
N
S1 S2
B
Fig.1 Circuit diagrams for Fibaro Switch.
NOTES FOR THE DIAGRAM:
S1 – terminal for key no. 1 (has the option of entering the device in
Danger of electrocution.
learning mode)
Note!
i
It is possible to supply the load with voltage other
than the power supply to Fibaro switch (e.g. different
phase or voltage or even DC. Detailed data are
contained in specifications and diagrams of Figure
1).
Durability of t he d evice depends on applied load. For
i
durability exceeds 200 000 switches. For inductive
L
N
flowing current should be limited to approx. 12A to
ensure reliable operation of the device for similar
long period.
TIPS FOR ARRANGING THE ANTENNA:
S1 S2
I
L
N
i
Locate the antenna as far from metal elements as
O
B
possible (connecting wires, bracket rings, etc.) in
SWITCH
order to prevent interferences.
i
Metal surfaces in the direct vicinity of the antenna
(e.g. flush mounted metal boxes, metal door frames)
may impair signal reception!
L
i
N
perfectly matched to the band in which the system
operates
alternative
power
supply
Note!
i
S1 S2
I
L
N
O
B
SWITCH
DICTIONARY:
enable user to add it to Fibaro system (Home Center)
radio system
of Fibaro system
III Activating Fibaro Switch
I
L
N
O
SWITCH
1. Installing the Fibaro Switch
STEP 1
Connect the device in accordance with the circuit diagram presented
[Adding/ Removing] Fibaro Switch [to/ from] Z-wave network
STEP 2
Fibaro Switch must be placed within the range of Home Center
controller, as adding mode requires direct communication with the
controller.
STEP 3
alternative
Find key no. 1 which allows to switch circuit 1 on, in accordance with
power
the diagram
supply
STEP 4
controller's manual)
I
L
N
STEP 5
O
Add Fibaro Switch to the network by pushing three times (sat) key
SWITCH
WARNING!
i
Fibaro Switch cancels the "learning" mode after key
no. 1 is pressed once. Therefore, pressing key no. 1
four times will not add the devices to the network.
WARNING!
i
Fibaro Switch is set by default to operate with
switch). While adding Fibaro Switch to the network
contacts are open (off), because closing them
prevent adding the device to the network.
During the installation it is recommended to use a
mono-stable keys or push- button B.
STEP 6
The controller indicates that when the device is correctly added to
the network, (see the manual of Home Center controller).
2. Resetting Fibaro Switch
Fibaro Switch provides two methods for resetting.
Method I : Reset by removing Fibaro Switch from the existing
network (see the manual of controller).
Method II
Fibaro Switch allows the user to reset settings by single pressing S1
key and then holding key S2
3. Controlling Fibaro Switch by mono-stable or
bi-stable switches.
mono-stable switch (after releasing the push-button a spring
automatically pushes back and disconnects the button )
corresponding to a chosen circuit (see diagram).
bi-stable switch (operates as a two-position switch, it has no
spring that would push back the device after releasing manual
pressure)
4. Controlling Fibaro Switch using a command: ALL
ON / ALL OFF
By default, Fibaro Switch accepts both active commands ALL ON
and ALL OFF. Settings may be changed by entering an appropriate
value into configuration register no. 1 (see configuration)
5. Controlling Fibaro Switch using Home Center
V Configuration
controller
After adding Fibaro Switch to the network, it will be represented in
The following settings are available in the Fibaro interface as simple
options that may be chosen by selecting the appropriate box
In order to configure Fibaro Switch (using the Home Center
2. Resetting Fibaro Switch
Fibaro Switch provides two methods for resetting.
Parameter no. 1 - Activate / deactivate functions ALL ON / ALL
OFF.
255
0
1
2
Parameter no. 3 - Automatic turning off relay after set time
default value 0
0
1
Fig. 2 Icon of Fibaro Switch shown by Home Center
Parameter no. 4 - Time after witch relay is automatically turned
controller
off. default value 200 (200ms)
By default, FGS211 device has a second hidden icon.
[1- 255] (10ms – 2,5s) time after relay is automatically turned off.
It represents the second, virtual channel of the device triggered by
the second key. The user may add the association to this channel or
trigger a scene.
Parameter no. 6 - Separation of association sending for group
no. 1 (key no. 1) default value 0
IV Association
to all associated devices in group no. 1.
Association enables Fibaro Switch to directly control a device
Shutter or scene (scene may be controlled only through the Home
associated devices in group no. 1. Turning on device douse not
Center controller).
causes sending of any command to all associated devices in group
no. 1. Double click of key causes turning on all associated devices,
dimmers are set to last remembered state.
WARNING!
i
Association ensures direct transfer of control
associated devices in group no. 1. Turning on device douse not
commands between devices, and is performed
causes sending of any command to all associated devices in group
without participation of the main controller.
no. 1. Double click of key causes turning on all associated devices,
Fibaro Switch provides association of three groups.
Shutter.
1st group is assigned to key no. 1
2nd group is assigned to key no. 2
Parameter no. 13 - This function allows user to change [on / off]
bi-stable keys (parameter no. 14) default value 0
3rd for controllers such Home Center for state reporting
0 [On / Off] changes key status.
MultiChannel devices in group no. 1 and no. 2, group no. 3 has only
1 ON is active after closing switch contacts. Off is active after
one field. The first field in each group is reserved for the network
opening switch contacts.
controller. It is recommended to use up to 10 devices, as the time
required by the device to send a command to each associated
device may be quite long.
Parameter no. 14 - Switch type connector, you may choose
To add an association (using the Home Center controller), go to
between mono-stable and bi-stable switches. default value 1
0
Select the "device options" tab. Then specify to which group and
1
what devices are to be associated. Sending relevant information to
devices added to associated groups may take even a few minutes.
Parameter no. 15 - Operation of the Dimmer and Roller Shutter
WARNING!
Controller - enabling this option allows the user to dim
i
When Fibaro Switch sends control commands and
lighting/shut roller by associating Dimmer/Roller Shutter
a new command is issued, then the current one
Controller and holding or double press of double switch (only
command transmission is interrupted to send new
mono-stable switch). default value 0
commands.
0
1
devices. Multichannel devices are devices that include two or more
circuits inside one physical unit.
Parameter no. 16 - Saving the state of the device after a power
failure. Fibaro Switch returns to the last position saved before
a power failure. default value 0
0
returns to "off" position
1