FIBARO SWIPE FGGC-001 Panduan Pengoperasian - Halaman 10
Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Pengontrol FIBARO SWIPE FGGC-001. FIBARO SWIPE FGGC-001 13 halaman. Swipe gesture controller
Halaman Cetak
18
3. LED diode - visual indicator settings
visual indication of gestures detection.
Available settings: 0 - gestures detection is not indicated
Default setting:
4. Buzzer - signalling result of gesture recognition
i
NOTE
Acoustic signalling of gesture recognition result (using the built-in
Parameter 4 is rele-
buzzer).
vant only if parameter
2 is set to 1.
Available settings: 1 - only successful recognition is signalled
Default setting:
5. Powering mode - interval of updating the current mode
This parameter determines how often the device checks if the uSB
power supply is connected and updates powering mode if needed.
Available settings: 0 - powering mode is not updated
Default setting:
6. Power saving mode (battery mode)
This parameter determines operation of gesture detection when bat-
tery powered.
When Standby Mode is selected, hold gesture must be performed to
exit power saving mode and reactivate normal gesture recognition.
The device in Standby Mode consumes the least battery life.
When Simple Mode mode is selected, gesture recognition is always
active, but only slowly performed gestures will be recognized proper-
ly (high battery consumption).
Available settings: 0 - Standby Mode
Default setting:
7. Hold gesture to enter the menu
!
CAUTION
This parameter allows to choose if the menu can be entered using the
After
disabling
the
hold gesture.
hold gesture in param-
eter 7, menu can be
Available settings: 0 - hold gesture to enter the menu enabled
entered by using the
B-button only!
Default setting:
ASSOCIATIOnS
1 - gestures detection is indicated
0
Parameter size:
1 [bytes]
2 - only failed recognition is signalled
3 - successful and failed recognition is signalled
3
Parameter size:
1 [byte]
1-1080 (in minutes) - time interval
4 (4 minutes) Parameter size:
2 [bytes]
1 - Simple Mode
2 - the Swipe does not enter power saving
mode
0
Parameter size:
1 [byte]
1 - hold gesture to enter the menu disabled
0 (enabled)
Parameter size:
1 [byte]
10. Scenes sent to the controller
Defines which actions result in sending scenes to 1st "Lifeline" group.
Available settings: 1 - scenes for flick uP gesture enabled
2 - scenes for flick DOWn gesture enabled
4 - scenes for flick LEFT gesture enabled
8 - scenes for flick RIGhT gesture enabled
16 - scenes for clockwise circular gesture ena-
bled
32 - scenes for counter-clockwise circular ges-
ture enabled
15
Default setting:
Parameter size:
11. Associations in Z-Wave network security mode
Parameter defines how commands are sent in specified association
groups: as secure or non-secure. Parameter is active only in Z-Wave
network security mode. It does not apply to 1st "Lifeline" association
group.
Available settings: 1 - 2nd group "Flick uP" sent as secure
2 - 3rd group "Flick DOWn" sent as secure
4 - 4th group „Flick LEFT" sent as secure
8 - 5th group „Flick RIGhT" sent as secure
16 - 6th group „Circular AirWheel" sent as secure
31
Default setting:
Parameter size:
12. Control mode of 2nd - 5th „Flick UP/DOWN/LEFT/RIGHT" asso-
ciation groups and scenes
Parameter allows to choose control mode for 2nd-5th groups and
scenes.
By default, Toggle Mode is active, meaning that a single flick turns On
the group and the same flick turns it OFF, doubled flicks are inactive.
After disabling Toggle Mode a single flick will turn the device On and
the same flick doubled will turn it OFF.
Available settings: 1 - Toggle Mode enabled for 2nd association
group
2 - Toggle Mode enabled for 3rd association
group
4 - Toggle Mode enabled for 4th association
group
8 - Toggle Mode enabled for 5th association
group
Default setting:
15
Parameter size:
19
i
NOTE
Parameter 10 values
may be combined,
e.g. 1+2=3 means that
scenes for flick uP and
DOWn are enabled.
1 [byte]
i
NOTE
Parameter 11 values
may be combined,
e.g. 1+2=3 means that
2nd & 3rd group are
sent as secure.
1 [byte]
i
NOTE
Parameter 12 values
may be combined,
e.g. 1+2=3 means that
2nd & 3rd group are
selected.
i
NOTE
Disabling Toggle Mode
will introduce delay
when performing sin-
gle gestures.
1 [byte]
ASSOCIATIOnS