FIBARO FIBEFGSD-002 Panduan Memulai Cepat
Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Alarm Asap FIBARO FIBEFGSD-002. FIBARO FIBEFGSD-002 9 halaman. Smoke sensor
Halaman Cetak
Fibaro Group
FIBARO Smoke Sensor
SKU: FIBEFGSD-002
Quickstart
This is a secure Alarm Sensor for Europe. To run this device please insert fresh 1 * CR123A batteries. Please make sure the internal battery is fully
charged. Fibaro Smoke Sensor inclusion:
1. Install the battery. Visual indicator will signal the Z-Wave network inclusion status (green - device included, red - device not included)
2. Make sure the device is located within direct range of the Z-Wave controller.
3. Set the main controller into the learning mode (see main controllers operating manual).
4. Quickly, triple click the B-button, located on Fibaro Smoke Sensors enclosure.
5. Fibaro Smoke Sensor will be detected and included in the Z-Wave network.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer,
distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this
equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and
every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is
not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-
Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this
device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level
of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
The FIBARO Smoke Sensor is a universal, ultra-light, perfectly designed, optical Z-Wave smoke detector. Fire alarm is signaled by sound, visual indicator blinking
and alarm reports sent to the other devices within Z-wave network. The optical sensor detects smoke at an early stage of fire, often before flames appear and
temperature starts to rise significantly. Moreover, the device has a built-in temperature sensor, which is adjustable to allow detection of fire by exceeding given
temperature threshold. The FIBARO Smoke Sensor is a battery powered device designed to be placed on the wall or ceiling. Visual indicator signals fire, operating
mode and it is used to check if the device is within the Z-wave network using a built-in Z-Wave range tester. The Smoke Sensor is designed to operate in confined
spaces, under normal conditions (lacking of smoke, dust or condensed water vapor).
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do
this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended
to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
1. Make sure the device has the battery installed.
2. Press and hold the B-button for 3 seconds. Visual indicator will glow white.
3. You will hear a short signal.
4. Release the B-button.
5. Wait until the visual indicator glows yellow, signaling entering the 4th menu level.
6. Press the B-button briefly to confirm menu level choice. At the same time you will hear a short beep, the same sound as during the power connection.
Successful reset will be confirmed with the visual indicator changing colour to red and fading. At the same time, short beep will sound, same as at the power
connection.
https://manual.zwave.eu/backend/make.php?lang=en&sku=FIBEFGSD-002
1/8