ACTOR-MATE Crossfire AL48 Series Panduan Pengguna - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Peralatan Pencahayaan ACTOR-MATE Crossfire AL48 Series. ACTOR-MATE Crossfire AL48 Series 4 halaman.

Halaman Cetak

Fuse Replacement

Always disconnect from main power supply before attempting to replace the fuse
Remove the old fuse from the holder and replace with the exact same type fuse.
Replacement with anything other than the specified part may damage your unit.

Trouble Shooting

If there is no light from the unit, please check the main power supply and fuse.
If unit does not respond to DMX, please check the DMX cables are connected
properly and are wired correctly.
If unit does not response to the music please check the sound-activation
adjustment.
If problems cannot be solved please contact your dealer for service
Cleaning
Use a soft cloth and normal glass cleaner to clean the outside casing and the
hexagonal reflection mirror. Cleaning frequency depends on the environment in which
the fixture operates. Be sure to dry all parts before plugging the unit back in.

Specifications

Model No.
AL48-05R/ 30R/ 50R/ 100R
Laser power
4.9/ 30/ 50/ 100mW x 2
Laser color
Red
Model No.
AL48-5R5G AL48-50R20G AL48-100R30G AL48-200R50G
Laser Power
4.9~200mW Red & 4.9~50mW Green
Laser color
Net Weight
Power
AC 100V~120V or 220V~240V 50/60HZ
Classification
4.9mW to 20mW: 3R/ 30mW to 200mW: 3B
Size (mm)
Fuse
Material
Beam Divergence
Op. Temperature
AL38-05G/ 20G/ 30G
4.9/ 20/ 30mW
Green
Red and Green
6.5kgs
L435 × W220 × H135
20mm×2A
Metal
< 1.5 mrad
18 ~ 25 ℃

Operating Modes

1. Stand-Alone Operation (Auto, Sound Active Mode)
Auto mode
The unit runs built-in program to change the laser effects automatically. Set
DIP switch pin 10 to ON, other pins to OFF to run Auto mode
Sound Active mode
This unit has built-in program that will react to sound and music under Sound
Active mode. Set all DIP switch pins to OFF to run Sound Active mode.
Please adjust "Sensitivity Adjustment Knob" to fine-tune the optimum level of
sound reaction.
2. Master-Slave Operation (Auto, Sound Active Mode)
This mode allows user to link up to 32 units to run the Master-Slave operation.
In the Master-Slave operation one unit will act as the controlling unit and the
others will react to the controlling unit. Daisy chain your units via the standard
XLR microphone cables in the following configuration: 'Out' from the first unit to
'In' on the second, 'Out' from the second to 'In' on the third and so on.
Auto mode
To set the master: Set DIP switch pin 10 and 11 to ON, other pins to OFF.
To set the slaves: Set pin 1 to ON, other pins to OFF
Sound Active mode
To set the master: Set DIP switch pin 11 to ON, other pins to OFF.
To set the slaves: Set pin 1 to ON, other pins to OFF
3. DMX Operation
DMX operation gives the users freedom to create their own programs tailored to
their own individual needs. To run this unit in DMX mode, connect the unit to
any standard DMX controller via XLR connectors. Please consult DMX
controller manual to determine address.
Function Selection Chart
DIP SWITCHES CHART
1
2
3
4
5
6
7
OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF N/A N/A
OFF OFF OFF OFF OFF OFF OFF OFF OFF ON N/A N/A
SET SOUND / AUTO MODE
ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF N/A
SET ADDRESS
FUNCTION
8
9
10
11
12
SOUND MODE
AUTO MODE
MASTER
ON N/A
SLAVE
DMX MODE
OFF OFF N/A