Sharp AR-M277 IMAGERs Panduan Operator Kunci - Halaman 20
Jelajahi secara online atau unduh pdf Panduan Operator Kunci untuk Semua dalam Satu Printer Sharp AR-M277 IMAGERs. Sharp AR-M277 IMAGERs 24 halaman. Digital multifunctional imager
Juga untuk Sharp AR-M277 IMAGERs: Spesifikasi (2 halaman), Panduan Pengaturan Perangkat Lunak (18 halaman), Panduan Pengaturan Perangkat Lunak (20 halaman), Panduan Referensi Cepat (39 halaman), Panduan Referensi Cepat (39 halaman)
Halaman Cetak
PROGRAMS FOR PRINT MODE
PORT SWITCHING METHOD
(When the PRINTER EXPANSION KIT is installed)
This program is used to set the method for switching
printer ports.
The machine can use the following three printer ports:
• Parallel port
• USB port
• Network port
The factory default setting is "SWITCH AT END OF
JOB".
Selections
SWITCH AT
Automatic printer port selection
END OF JOB
at the end of each print job.
SWITCH AFTER
Automatic printer port selection if
I/O TIMEOUT
the time set in "I/O TIMEOUT"
elapses.
ENABLE PARALLEL PORT
(When the PRINTER EXPANSION KIT is installed)
This program is used to enable or disable printing via
the parallel port.
This program is initially enabled (factory default
setting).
ENABLE USB PORT
(When the PRINTER EXPANSION KIT is installed)
This program is used to enable or disable printing via
the USB port.
This program is initially enabled (factory default
setting).
ENABLE NETWORK PORT
(When the PRINTER EXPANSION KIT is installed)
This program is used to enable or disable printing via
the network port.
This program is initially enabled (factory default
setting).
ENABLE ECP
(When the PRINTER EXPANSION KIT is installed)
Enable this program when you wish to use ECP mode
on the parallel port.
This program is initially disabled (factory default
setting).
18
Description
NETWORK SETTINGS
(When the PRINTER EXPANSION KIT is installed)
The NETWORK SETTINGS are used when the
machine is used as a network printer. The "NETWORK
SETTINGS" consist of the following programs:
G IP ADDRESS SETTING
G ENABLE TCP/IP *
G ENABLE NetWare *
G ENABLE EtherTalk *
G ENABLE NetBEUI *
G RESET THE NIC
* When the PRINT SERVER CARD is installed.
Consult your network administrator
Caution
before configuring the NETWORK
SETTINGS.
• After changing the settings, you must turn
Note
off the machine's power switch, wait
briefly, and then turn the switch back on in
order to make the changes take effect.
• Some programs in the following are
marked by "*1". This indicates that a
message will appear at the end of the
setting procedure asking you to confirm
execution of the new setting. If needed,
you can cancel the new setting by
touching the [NO] key.
IP ADDRESS SETTING
This program is used to set the IP address (IP
address, Subnet Mask, and Gateway) of the machine
when TCP/IP protocol is used on the network.
When "DHCP" is selected, the machine will obtain an IP
address automatically. This is the factory default setting.
When the print server card is installed and the
machine is used on a TCP/IP network, be sure to
enable the "ENABLE TCP/IP" program.
When DHCP is used, the IP address
Caution
assigned to the machine may
automatically be changed on
occasion. If this happens, printing
will not be possible.
ENABLE TCP/IP
This program must be enabled to use the machine on
a TCP/IP network. "IP ADDRESS SETTING" must
also be configured.
This program is initially enabled (factory default setting).
ENABLE NetWare
This program must be enabled to use the machine on
a network that uses NetWare protocol.
This program is initially enabled (factory default setting).
ENABLE EtherTalk
This program must be enabled to use the machine on
a network that uses EtherTalk protocol.
This program is initially enabled (factory default setting).