DIGITAL DELAY Mega 400 Petunjuk Manual - Halaman 7

Jelajahi secara online atau unduh pdf Petunjuk Manual untuk Aksesori Mobil DIGITAL DELAY Mega 400. DIGITAL DELAY Mega 400 14 halaman.

Setting Push-button Mode and the

To set the Push-button Mode, repeatedly press the D key until the letters A and B are shown next to the P.B. Mode

and the S.F.O. Mode (D2). The Push-button Mode is shown next to the letter A. The left most digit shows "1" or " 2" to

indicate which Push-button Mode the unit is in, when in 1 Push-button Mode, the First P.B. starts both the primary and

secondary delays. When in 2 Push-button Mode, one or both push-buttons can be used in any sequence, the First P.B. starts

the primary and Second P.B. starts the secondary delay. The two right digits show the programmable amount of time (00 to 99

seconds) that after the Transbrake releases, Button 1 and Button 2 push-button inputs are disabled. To change either the

Button Mode or the Interrupt Time first press the A key, then enter a "1" or "2" for the Push-button Mode followed by a two

digit number representing the Push-button Interrupt Time. For example "1 10" would indicate 1 Push-button Mode with a 10

second Interrupt Time. If no Push-button Interrupt Time is wanted enter "00" after pressing a "1" or "2" for the Push-button

Mode.

To set the Selectable Function Output Mode, repeatedly press the D key until the letters A and B are shown next to

the P.B. Mode and the S.F.O. Mode (D2). The S.F.O. Mode is shown next to the letter B. There are five different modes (1-5)

which are listed below, to change the S.F.O. mode repeatedly press the "B" key, each time the B key is pressed the S.F.O.

mode will increase by one until it reaches five at which time it will revert back to one on the next press of the B key.

This sets the S.F.O. terminal up to Function as a Starting Line Enhancer (S.L.E.).

This sets the S.F.O. terminal up to function as a second Throttle Stop.

This sets the S.F.O. terminal up to function as a Line Lock Control.

This sets the S.F.O. terminal up to function as a second Transbrake output.

This turns the S.F.O. terminal completely off (no voltage out).

If the S.F.O. mode is set to mode one the Starting Line Enhancer will be turned on, if the S.F.O. mode is set to any

mode other than mode one, the Starting Line Enhancer will be turned off. To set the Starting Line Enhancer Time, repeatedly

press the D key until the letters A and B are shown next to the S.L.E. and the P.T.S.O. (D3). If there are two dashes and the

word off is shown at the top of the screen, the Starting Line Enhancer is turned off. If the Starting Line Enhancer is turned on,

the time is shown to the right of the letter A. The four digits show the amount of time that the throttle will open up before the

TRANSBRAKE RELEASES.

When the Starting Line Enhancer is turned on, to enter a new time do the following. Press the A key, the four digits

to the right of the letter A will go blank. Then use the numerical keys to enter a new Starting Line Enhancer time. All number

from 00.00 to 99.99 can be entered, with the exceptions of 11.11 and 22.22 which are described below. If the Starting Line

Enhancer time is greater than the delay time, the throttle will open as soon as a Transbrake push-button is released. If this is

desired simply enter all nines (99.99). If all zeros (00.00) are entered the throttle will open up when the Transbrake releases.

Using all ones (11.11) will pre-set the release of the throttle at eight tenths of a second before the Transbrake releases.

This means that two tenths of a second after your top yellow the throttle will open up. The benefit of the throttle opening up at

this time is that it will not be a distraction when using your top yellow for a second hit at the tree.

Using all twos (22.22) will set the S.L.E. to Pro mode. When in Pro mode the release of the throttle will occur when

the transbrake is engaged. This means that the throttle must be closed using the Tap P.B. before staging.

Note:

Use Throttle Stop Mode two (D4) to change output voltage of the S.F.O. for the type of Throttle

Stop being used as a Starting Line Enhancer.

Push-button Interrupt Time

Setting Selectable Function

Output Mode (S.F.O.)

Setting Starting Line

Enhancer Time